Komatsu PW98MR-10 Operation & Maintenance Manual page 439

INDEX
F/N/R override switch............................................3-99
F/N/R pilot lamp.................................................... 3-40
F/N/R switch..........................................................3-95
Fan belt tension - Check / Replace.......................4-67
Fan switch...........................................................3-199
Filter........................................................................ 4-6
Fire extinguisher................................................. 3-121
Fresh and clean lubricants......................................4-2
Freshrecirc air changeover switch...................... 3-202
Front and rear axle joints...................................... 4-38
Front axle - Change oil..........................................4-62
Front axle - Check oil level....................................4-43
Front axle swing joint - Lubricating....................... 4-37
Front working lamps switch...................................3-90
Fuel......................................................................... 4-4
Fuel - Check level / Add......................................3-133
Fuel and lubricants to match the ambient temperature
.........................................................................4-3
Fuel circuit - Bleed air......................................... 3-225
Fuel consumption gauge.......................................3-34
Fuel consumption gauge - Set display..................3-66
Fuel consumption record - Check......................... 3-64
Fuel control dial.....................................................3-93
Fuel gauge............................................................ 3-32
Fuel main filter cartridge - Replace....................... 4-65
Fuel prefilter cartridge - Replace...........................4-49
Fuel spray prevention cap - check for missing and
hardening of rubber....................................... 4-80
Fuel tank - Drain water and sediment................. 3-127
Function switches................................................. 3-52
Function switches and guidance icons................. 3-44
Fuse.................................................................... 3-118
Fusible link.......................................................... 3-119
Gas spring - Check............................................... 4-30
Gear engagement caution lamp............................3-25
General attachment such as crusher - Operate....6-18
General precautions common to operation and main-
tenance.......................................................... 2-16
General view........................................................... 3-2
GPS synchronization - Set....................................3-81
Grease.................................................................... 4-5
Ground whole the bottom side of blade to support
machine....................................................... 3-178
Guide to reduce vibration levels on machine.......... 1-6
Handle electrical components.................................4-7
Handling bucket with hook...................................... 6-8
Handling quick coupler............................................6-4
Hazard switch....................................................... 3-94
High beam switch..................................................3-92
High-pressure hoses and pipings - Handle...........2-45
Horn - Check.......................................................3-136
F
G
H
WENAM00061
Horn push button.................................................. 3-97
Hydraulic breaker..................................................6-21
Hydraulic circuit.....................................................6-11
Hydraulic circuit - Bleed air................................... 4-31
Hydraulic circuit - Connect.................................... 6-11
Hydraulic oil filter element - Replace.................... 4-59
Hydraulic oil temperature caution lamp.................3-21
Hydraulic oil temperature gauge........................... 3-32
Hydraulic quick coupler system caution lamp....... 3-25
Hydraulic system - Warm-up operation...............3-156
Hydraulic system caution lamp............................. 3-21
Hydraulic tank - Change oil, clean tank strainer...........
...............................................................4-68,4-81
Hydraulic tank - Check oil level / Add oil.............3-129
Hydraulic tank - Drain........................................... 4-55
Hydraulic tank breather element - Replace...........4-55
If any problem is found..........................................2-17
If machine monitor shows warning display......... 3-236
Incorrect steering mode pilot lamp........................3-42
Incorrect travel speed pilot lamp........................... 3-38
Indicator for signalling the rear wheels are not aligned
.......................................................................3-43
Indicator signalling turret alignment...................... 3-27
Indicator signalling unlocking of emergency rotation...
.......................................................................3-27
Indicator signalling wheel alignment..................... 3-39
Indicator signalling wrong steering selection for trav-
elling on roads............................................... 3-39
Initial 100 hours maintenance (only after the first 100
hours).............................................................4-13
Initial 250 hours maintenance (only after the first 250
hours).............................................................4-13
Initial 50 hours maintenance (only after the first 50
hours).............................................................4-13
Initial 500 hours maintenance (only after the first 500
hours).............................................................4-13
Inside operator's compartment............................. 2-17
Inspecting machine............................................... 2-16
Install attachment..................................................6-20
Introduction............................................................. 1-8
Investigate and confirm jobsite conditions............ 2-25
KCCV filter element - Replace.............................. 4-75
Keep machine clean............................................. 2-16
Keep work place clean and tidy............................ 2-39
Komatsu Closed Crankcase Ventilation (KCCV) 3-123
Komatsu genuine lubricants....................................4-2
Komatsu genuine replacement parts...................... 4-2
KOMTRAX.......................................................... 3-123
Language settings.................................................3-83
Left front mirrors - Adjust.................................... 3-140
I
K
L
8-3