Huawei S9300 Configuration Manual page 228

S9300&S9300E Terabit Routing Switch
Configuration Guide - IP Service
3.
4.
Issue 01 (2012-03-15)
[PE1-ospf-1-area-0.0.0.0] network 1.1.1.9 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] network 4.3.5.0 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit
# Configure OSPF on PE2 and trigger the setup of the LSP.
[PE2] ospf
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] network 4.3.5.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit
Configure a peer of the 6PE.
# Configure IBGP on PE1, enable the peer 6PE capability, and import the direct and static
routes of IPv6.
[PE1] bgp 65100
[PE1-bgp] peer 2.2.2.9 as-number 65100
[PE1-bgp] peer 2.2.2.9 connect-interface loopback 0
[PE1-bgp] ipv6-family
[PE1-bgp-af-ipv6] import-route direct
[PE1-bgp-af-ipv6] import-route static
[PE1-bgp-af-ipv6] peer 2.2.2.9 enable
[PE1-bgp-af-ipv6] peer 2.2.2.9 label-route-capability
[PE1-bgp-af-ipv6] quit
[PE1-bgp] quit
# Configure IBGP on PE2, enable the peer 6PE capability, and import the direct and static
routes of IPv6.
[PE2] bgp 65100
[PE2-bgp] peer 1.1.1.9 as-number 65100
[PE2-bgp] peer 1.1.1.9 connect-interface loopback 0
[PE2-bgp] ipv6-family
[PE2-bgp-af-ipv6] import-route direct
[PE2-bgp-af-ipv6] import-route static
[PE2-bgp-af-ipv6] peer 1.1.1.9 enable
[PE2-bgp-af-ipv6] peer 1.1.1.9 label-route-capability
[PE2-bgp-af-ipv6] quit
[PE2-bgp] quit
Set the IPv6 address and static route for the CE interface.
# Configure CE1 to set up the connection between the IPv6 and PE1.
<Quidway> system-view
[Quidway] sysname CE1
[CE1] ipv6
[CE1] vlan batch 100
[CE1] interface gigabitethernet 1/0/0
[CE1-GigabitEthernet1/0/0] port hybrid pvid vlan 100
[CE1-GigabitEthernet1/0/0] port hybrid untagged vlan 100
[CE1-GigabitEthernet1/0/0] quit
[CE1] interface vlanif 100
[CE1-Vlanif100] ipv6 enable
[CE1-Vlanif100] ipv6 address 3000:435::2 64
[CE1-Vlanif100] quit
[CE1] ipv6 route-static :: 0 vlanif 100
# Configure CE2 to set up the IPv6 connection with PE1.
<Quidway> system-view
[Quidway] sysname CE2
[CE2] ipv6
[CE2] vlan batch 100
[CE2] interface gigabitethernet 1/0/0
[CE2-GigabitEthernet1/0/0] port hybrid pvid vlan 100
[CE2-GigabitEthernet1/0/0] port hybrid untagged vlan 100
[CE2-GigabitEthernet1/0/0] quit
[CE2] interface vlanif 100
[CE2-Vlanif100] ipv6 enable
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11 IPv6 over IPv4 Tunnel Configuration
217