Table of Contents
Advertisement
ADJUST
■ ADJ-XY
COPIER> ADJUST> ADJ-XY
ADJ-X
Adj of img pstn in book mode: vert scan
Details
To adjust the image reading start position (image leading edge position)
in vertical scanning direction.
When replacing the Scanner Unit or Main Controller PCB/clearing the
Reader-related RAM data, enter the value of service label.
When the non-image width is larger than the standard value, set the
smaller value.
When out of original area is copied, set the larger value.
As the value is incremented by 1, the image position moves to the
trailing edge side by 0.1 mm.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-30 to 30
Unit
0.1 mm
Default value
0
ADJ-Y
Adj of img pstn in book mode: horz scan
Details
To adjust the image reading start position in horizontal scanning
direction.
When replacing the Scanner Unit or Main Controller PCB/clearing the
Reader-related RAM data, enter the value of service label.
When the non-image width is larger than the standard value, set the
smaller value.
When out of original area is copied, set the larger value.
As the value is incremented by 1, the image position moves to the rear
side by 0.1 mm.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-15 to 15
Unit
0.1 mm
Default value
0
8
Service Mode > COPIER > ADJUST > ADJ-XY
8
Service Mode > COPIER > ADJUST > ADJ-XY
COPIER> ADJUST> ADJ-XY
ADJ-Y-DF
Adj img pstn in DADF mode:horz scan[Frt]
Details
To adjust the image reading start position in horizontal scanning direction
at DADF reading.
When replacing the Scanner Unit or Main Controller PCB/clearing the
Reader-related RAM data, enter the value of service label.
As the value is incremented by 1, the image position moves to the rear
side by 0.1 mm.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-15 to 15
Unit
0.1 mm
Default value
0
ADJ-X-MG
Fine adj img ratio: book mode, vert scan
Details
To make a fine adjustment of image magnification ratio in vertical
scanning direction at copyboard reading.
When replacing the Scanner Unit or Main Controller PCB/clearing the
Reader-related RAM data, enter the value of service label.
As the value is incremented by 1, the image magnification ratio changes
by 0.01 %.
+: Enlarge
-: Reduce
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-200 to 200
Unit
0.01 %
Default value
0
8-22
8-22
Advertisement
Table of Contents
Troubleshooting
