Canon imageRUNNER C1335 Series Service Manual page 375

Error Detail
Item
code Code
E001 A004 Title Fixing Main Thermistor high temperature detection error
Description The Fixing Main Thermistor detected 270 deg C or higher.
Remedy [Related parts]
• Fixing Assembly (Unit of replacement: Fixing Assembly)
• Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER
SUPPLY ASSEMBLY)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage
Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK
ASSEMBLY)
• Harness between the Low-voltage Power Supply PCB (UN01/J315
and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of
replacement: CABLE, POWER SUPPLY)
• Harness between the Fixing Drawer (DR01/J5401) and the DC
Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK
ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
E001 A005 Title Fixing Sub Thermistor (Front) high temperature detection error
Description The Fixing Sub Thermistor (Front) detected 295 deg C or higher.
Remedy [Related parts]
• Fixing Assembly (Unit of replacement: Fixing Assembly)
• Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER
SUPPLY ASSEMBLY)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage
Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK
ASSEMBLY)
• Harness between the Low-voltage Power Supply PCB (UN01/J315
and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of
replacement: CABLE, POWER SUPPLY)
• Harness between the Fixing Drawer (DR01/J5401) and the DC
Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK
ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7 Error•Jam•Alarm > Error Code > Error Code Details
Error Detail
Item
code Code
E001 A006 Title Fixing Sub Thermistor (Rear) high temperature detection error
Description The Fixing Sub Thermistor (Rear) detected 295 deg C or higher.
Remedy [Related parts]
• Fixing Assembly (Unit of replacement: Fixing Assembly)
• Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER
SUPPLY ASSEMBLY)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage
Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK
ASSEMBLY)
• Harness between the Low-voltage Power Supply PCB (UN01/J315
and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of
replacement: CABLE, POWER SUPPLY)
• Harness between the Fixing Drawer (DR01/J5401) and the DC
Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK
ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
E002 A001 Title Fixing Main Thermistor temperature increase detection error
Description The Fixing Main Thermistor detected a temperature increase of 1 deg C
for less than 5 sec from turning ON the main power until start of PI control.
Remedy [Related parts]
• Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER
SUPPLY ASSEMBLY)
• Fixing Assembly (Unit of replacement: Fixing Assembly)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage
Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK
ASSEMBLY)
• Harness between the Low-voltage Power Supply PCB (UN01/J315
and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of
replacement: CABLE, POWER SUPPLY)
• Harness between the Fixing Drawer (DR01/J5401) and the DC
Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK
ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
7-4
Description
7-4