Canon imageRUNNER C1335 Series Service Manual page 518

■ SPLMAN
COPIER> FUNCTION> SPLMAN
SPL14159 Fixing of USB device ID
Details To fix the USB device ID to "000000000000".Driver for each machine
is installed to a PC. However, by fixing the serial number, the PC
considers that any connected machine to be the same machine; thus,
there will be no need to install the drivers many times.
Adj/set/operate method 1) Enter the value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SPL65677 Increase of paper leading edge margin
Details To increase the margin on the leading edge of paper.
As the value is incremented by 1, the margin is increased by 0.1 mm.
If the setting is incompatible with SPL68676 (decrease of margin), the
setting is disabled (the margin will be standard).
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL68676
SPL68676 Decrease of paper leading edge margin
Details To decrease the margin on the leading edge of paper.
As the value is incremented by 1, the margin is decreased by 0.1 mm.
If the setting is incompatible with SPL65677(increase of margin), the
setting is disabled (the margin will be standard).
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL65677
SPL68677 Increase of paper right and left margins
Details To increase the margins on the right and left edges of paper.
As the value is incremented by 1, the margin is increased by 0.1 mm.
If the setting is incompatible with SPL25607 (decrease of margins), the
setting is disabled (the margins will be standard).
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL25607
8
Service Mode > COPIER > FUNCTION > SPLMAN
8 Service Mode > COPIER > FUNCTION > SPLMAN
COPIER> FUNCTION> SPLMAN
SPL25607 Decrease of paper right and left margins
Details To decrease the margins on the right and left edges of paper. As the
value is incremented by 1, the margin is decreased by 0.1 mm.If the
setting is incompatible with SPL68677 (increase of margins), the
setting is disabled (the margins will be standard).
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL68677
SPL93822 Setting of department ID count all clear
Details To set whether to disable clearing of all department ID counts.
Use case Used to prevent the value of the department ID counter from being
unintentionally cleared
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Be sure to perform this mode after consulting with the system
administrator at user's site.
Display/adj/set range 0 to 1
0: Enabled, 1: Disabled
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL78788
SPL78788 Setting to avoid clearing of department ID counts
Details To set whether to disable clearing of department ID count.
Use case Used to prevent the value of the department ID counter from being
unintentionally cleared
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Be sure to perform this mode after consulting with the system
administrator at user's site.
Display/adj/set range 0 to 1
0: Enabled, 1: Disabled
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL93822
SPL71100 Setting of the duty of Off-hook PCB
Details This is the mode to make handsets of particular manufacturers to be
rung when fax reception mode is set to "FAX/TEL switching".
Display/adj/set range 1 to 99
Default value 50
SPL00171 Change of the maximum value of auto sleep shift time
Details To change the maximum value of auto sleep shift time in Settings/
Registration> Timer Settings> Auto Sleep Time.
Use case When changing the setting time to shift to auto sleep mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Default value 0 (For Europe), 1 (For locations other than Europe)
8-79
8-79