Canon imageRUNNER C1335 Series Service Manual page 391

Error Detail
Item
code Code
E025 0110 Title Bottle Motor (YM) error (Y)
Description The Bottle Rotation Sensor (Y) did not detect rotation for 5 times in a row
although 0.8 sec (2 sec in the case of right before replacement of the
Toner Container) has passed after the Bottle Motor (YM) was turned ON.
Remedy [Related parts]
• Toner Container (Y)
• Harness between the DC Controller PCB (UN04/J155) and the Bottle
Motor (YM) (M09/J6301) (Unit of replacement: CABLE, MAIN)
• Harnesses from the DC Controller PCB to the Bottle Rotation Sensor (Y)
1. DC Controller PCB (UN04/J151) to Relay Connector (3P) (Unit of
replacement: CABLE, MAIN)
2. Relay Connector (3P) to Bottle Rotation Sensor (Y) (PS06/J5301)
(Unit of replacement: CABLE, BOTTLE SENSOR, Y/C)
• Bottle Rotation Sensor (Y) (PS06) (Unit of replacement: PHOTO
INTERRUPTER)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Bottle Drive Unit (YM) (Unit of replacement: BOTTLE DRIVE
ASSEMBLY)
• Hopper Unit (Y) (Unit of replacement: HOPPER ASSEMBLY)
[Points to note at work]
• Be sure to turn over the Door Lock Lever when removing the Bottle
Drive Unit (YM) and rotating the drive section by hand.
• When checking the harness/cable or connector, perform the following
work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
E025 0168 Title No toner detection error (Y)
Description The state without toner was detected although the recovery sequence was
performed for 5 times after replacement of the Toner Container (Y).
Remedy [Related parts]
• Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY)
• Hopper Unit (Y) (Unit of replacement: HOPPER ASSEMBLY)
• Toner Bottle Mount Unit (Y) (Unit of replacement: BOTTLE MOUNT
ASSEMBLY)
• Drum Unit (Y) (Unit of replacement: DEVE_UNIT_Y)
• Toner Container (Y)
[Remedy] Check/replace the related parts.
[Reference] If a user inserts an empty Toner Container (Y) repeatedly, the
error may occur.
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7 Error•Jam•Alarm > Error Code > Error Code Details
Error Detail
Item
code Code
E025 0210 Title Bottle Motor (YM) error (M)
Description The Bottle Rotation Sensor (M) did not detect rotation for 5 times in a
row although 1.5 sec (2 sec in the case of right before replacement of the
Toner Container) has passed after the Bottle Motor (YM) was turned ON.
Remedy [Related parts]
• Toner Container (M)
• Harness between the DC Controller PCB (UN04/J155) and the Bottle
Motor (YM) (M09/J6301) (Unit of replacement: CABLE, MAIN)
• Harnesses from the DC Controller PCB to the Bottle Rotation Sensor (M)
1. DC Controller PCB (UN04/J151) to Relay Connector (3P) (Unit of
replacement: CABLE, MAIN)
2. Relay Connector (3P) to Bottle Rotation Sensor (M) (PS07/J5302)
(Unit of replacement: CABLE, BOTTLE SENSOR, M/K)
• Bottle Rotation Sensor (M) (PS07) (Unit of replacement: PHOTO
INTERRUPTER)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Bottle Drive Unit (YM) (Unit of replacement: BOTTLE DRIVE
ASSEMBLY)
• Hopper Unit (M) (Unit of replacement: HOPPER ASSEMBLY)
[Points to note at work]
• Be sure to turn over the Door Lock Lever when removing the Bottle
Drive Unit (YM) and rotating the drive section by hand.
• When checking the harness/cable or connector, perform the following
work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
E025 0268 Title No toner detection error (M)
Description The state without toner was detected although the recovery sequence was
performed for 5 times after replacement of the Toner Container (M).
Remedy [Related parts]
• Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY)
• Hopper Unit (M) (Unit of replacement: HOPPER ASSEMBLY)
• Toner Bottle Mount Unit (M) (Unit of replacement: BOTTLE MOUNT
ASSEMBLY)
• Drum Unit (M) (Unit of replacement: DEVE_UNIT_M)
• Toner Container (M)
[Remedy] Check/replace the related parts.
[Reference] If a user inserts an empty Toner Container (M) repeatedly, the
error may occur.
7-20
Description
7-20