Canon imageRUNNER C1335 Series Service Manual page 569

TESTMODE > PRINT
DENS-Y Adj of Y-color density at test print
Details To adjust Y-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 255
Default value 128
DENS-M Adj of M-color density at test print
Details To adjust M-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 255
Default value 128
DENS-C Adj of C-color density at test print
Details To adjust C-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 255
Default value 128
DENS-K Adj of Bk-color density at test print
Details To adjust Bk-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 255
Default value 128
SW-Y Y-color output setting at test print
Details To make a setting of Y-color output for test print.
The setting is applied to all types.
When setting "SW-Y" to 1 and other items to "0", a single Y-color is
output.
Use case At test print
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 1
0: Not output, 1: Output
Default value 1
8
Service Mode > TESTMODE > PRINT
8 Service Mode > TESTMODE > PRINT
TESTMODE > PRINT
SW-M M-color output setting at test print
Details To make a setting of M-color output for test print.
The setting is applied to all types.
When setting "SW-M" to 1 and other items to "0", a single M-color is
output.
Use case At test print
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 1
0: Not output, 1: Output
Default value 1
SW-C C-color output setting at test print
Details To make a setting of C-color output for test print.
The setting is applied to all types.
When setting "SW-C" to 1 and other items to "0", a single C-color is
output.
Use case At test print
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 1
0: Not output, 1: Output
Default value 1
SW-K Bk-color output setting at test print
Details To make a setting of Bk-color output for test print.
The setting is applied to all types.
When setting "SW-K" to 1 and other items to "0", a single Bk-color is
output.
Use case At test print
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 1
0: Not output, 1: Output
Default value 1
MONOMODE Setting of PG full color/single color
Details To set for the output in full color/monochrome color with PG.
Use case When separating (identifying) the cause whether it's due to color or
monochrome.
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 1
0: Full color, 1: Single color
Default value 0
8-130
8-130