Table of Contents
Advertisement
COPIER> ADJUST> HV-TR
2TR-PA-1
Sec trn ATVC ctrl ppr allot V: punch 1st
Details
To adjust the paper allotted voltage applied to the 1st side of pre-
punched paper at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-PA-2
Sec trn ATVC ctrl ppr allot V: punch 2nd
Details
To adjust the paper allotted voltage applied to the 2nd side of pre-
punched paper at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-EN-1
Sec trn ATVC ctrl ppr allot V: envlp 1st
Details
To adjust the paper allotted voltage applied to the 1st side of envelope
at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
8
Service Mode > COPIER > ADJUST > HV-TR
8
Service Mode > COPIER > ADJUST > HV-TR
COPIER> ADJUST> HV-TR
2TR-EN-2
Sec trn ATVC ctrl ppr allot V: envlp 2nd
Details
To adjust the paper allotted voltage applied to the 2nd side of envelope
at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-P-1
Sec trn ATVC ctrl ppr allot V: crd 1st
Details
To adjust the paper allotted voltage applied to the 1st side of postcard at
secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-P-2
Sec trn ATVC ctrl ppr allot V: crd 2nd
Details
To adjust the paper allotted voltage applied to the 2nd side of postcard
at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
8-59
8-59
Advertisement
Table of Contents
Troubleshooting
