Table of Contents
Advertisement
COPIER> ADJUST> HV-TR
T2TR-N1
Adj of lead edge weak bias: pln ppr 1
Details
To adjust the offset of the leading edge weak bias for plain paper 1.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low (transfer
is weak).
Use case
When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
Use this item only when an image failure occurs.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
T2TR-N2
Adj of lead edge weak bias: pln ppr 2
Details
To adjust the offset of the leading edge weak bias for plain paper 2.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low (transfer
is weak).
Use case
When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
Use this item only when an image failure occurs.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
T2TR-N3
Adj of lead edge weak bias: pln ppr 3
Details
To adjust the offset of the leading edge weak bias for plain paper 3.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low (transfer
is weak).
Use case
When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
Use this item only when an image failure occurs.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
8
Service Mode > COPIER > ADJUST > HV-TR
8
Service Mode > COPIER > ADJUST > HV-TR
COPIER> ADJUST> HV-TR
T2TR-R1
Adj of lead edge weak bias: rcycl ppr 1
Details
To adjust the offset of the leading edge weak bias for recycled paper 1.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low (transfer
is weak).
Use case
When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
Use this item only when an image failure occurs.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
T2TR-R2
Adj of lead edge weak bias: rcycl ppr 2
Details
To adjust the offset of the leading edge weak bias for recycled paper 2.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low (transfer
is weak).
Use case
When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
Use this item only when an image failure occurs.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
T2TR-R3
Adj of lead edge weak bias: rcycl ppr 3
Details
To adjust the offset of the leading edge weak bias for recycled paper 3.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low (transfer
is weak).
Use case
When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
Use this item only when an image failure occurs.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
8-60
8-60
Advertisement
Table of Contents
Troubleshooting
