Table of Contents
Advertisement
COPIER> ADJUST> CCD
100-RG
RG clr displace crrct: 600dpi book mode
Details
To correct the color displacement (R and G lines) in vertical scanning
direction due to the Scanner Unit (paper front) occurs at copyboard
reading with 600 dpi.
When replacing the Scanner Unit, enter the value of service label on the
unit.
When replacing the Main Controller PCB/clearing the Reader-related
RAM data, enter the value of the service label on the reader.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-512 to 512
Unit
0.001 line
Default value
-333
100-GB
GB clr displace crrct: 600dpi book mode
Details
To correct the color displacement (G and B lines) in vertical scanning
direction due to the Scanner Unit (paper front) occurs at copyboard
reading with 600 dpi.
When replacing the Scanner Unit, enter the value of service label on the
unit.
When replacing the Main Controller PCB/clearing the Reader-related
RAM data, enter the value of the service label on the reader.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-512 to 512
Unit
0.001 line
Default value
333
8
Service Mode > COPIER > ADJUST > CCD
8
Service Mode > COPIER > ADJUST > CCD
COPIER> ADJUST> CCD
50DF-RG
RG clr displace crrct: 300dpi DADF mode
Details
To correct the color displacement (R and G lines) in vertical scanning
direction due to the Scanner Unit (paper front) occurs at DADF reading
with 300 dpi.
When replacing the Scanner Unit, enter the value of service label on the
unit.
When replacing the Main Controller PCB/clearing the Reader-related
RAM data, enter the value of the service label on the reader.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-512 to 512
Unit
0.001 line
Default value
-333
50DF-GB
GB clr displace crrct: 300dpi DADF mode
Details
To correct the color displacement (G and B lines) in vertical scanning
direction due to the Scanner Unit (paper front) occurs at DADF reading
with 300 dpi.
When replacing the Scanner Unit, enter the value of service label on the
unit.
When replacing the Main Controller PCB/clearing the Reader-related
RAM data, enter the value of the service label on the reader.
Use case
• When replacing the Scanner Unit
• When replacing the Main Controller PCB/clearing the Reader-related
RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
2) Turn OFF/ON the main power switch.
Caution
After the setting value is changed, write the changed value in the service
label.
Display/adj/set range
-512 to 512
Unit
0.001 line
Default value
333
8-26
8-26
Advertisement
Table of Contents
Troubleshooting
