Table of Contents
Advertisement
COPIER> ADJUST> HV-TR
2TR-H2-2
Sec trn ATVC ctrl ppr allot V: hvy2 2nd
Details
To adjust the paper allotted voltage applied to the 2nd side of heavy
paper 2 at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-H3-1
Sec trn ATVC ctrl ppr allot V: hvy3 1st
Details
To adjust the paper allotted voltage applied to the 1st side of heavy
paper 3 at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-H3-2
Sec trn ATVC ctrl ppr allot V: hvy3 2nd
Details
To adjust the paper allotted voltage applied to the 2nd side of heavy
paper 3 at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
8
Service Mode > COPIER > ADJUST > HV-TR
8
Service Mode > COPIER > ADJUST > HV-TR
COPIER> ADJUST> HV-TR
2TR-CP-1
Sec trn ATVC ctrl ppr allot V: color 1st
Details
To adjust the paper allotted voltage applied to the 1st side of color paper
at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-CP-2
Sec trn ATVC ctrl ppr allot V: color 2nd
Details
To adjust the paper allotted voltage applied to the 2nd side of color
paper at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
2TR-O-1
Sec trn ATVC ctrl ppr allot V:transp 1st
Details
To adjust the paper allotted voltage applied to the 1st side of
transparency at secondary transfer ATVC control.
When mottled image occurs, increase the value if it is due to insufficient
secondary transfer current and decrease the value if it is due to
overcurrent.
Use case
When adjusting the secondary transfer bias individually according to
paper type and 1st/2nd side
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and press
Start key.
Display/adj/set range
-128 to 127
Unit
30 V
Default value
0
8-57
8-57
Advertisement
Table of Contents
Troubleshooting
