Table of Contents
Advertisement
■ USER
COPIER> OPTION> USER
COUNTER1
Display of software counter 1
Details
To display counter type for software counter 1 on the Counter Check
screen.
Use case
Upon user/dealer's request
Adj/set/operate method N/A (Display only)
Caution
Display only. No change is available.
Display/adj/set range
0 to 999
0: Not registered
Default value
Refer to the specification of counter display because it differs according
to the model or the location.
COUNTER2
Setting of software counter 2
Details
To set counter type for software counter 2 on the Counter Check screen.
Use case
Upon user/dealer's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 999
0: Not registered
Default value
Refer to the specification of counter display because it differs according
to the model or the location.
COUNTER3
Setting of software counter 3
Details
To set counter type for software counter 3 on the Counter Check screen.
Use case
Upon user/dealer's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 999
0: Not registered
Default value
Refer to the specification of counter display because it differs according
to the model or the location.
COUNTER4
Setting of software counter 4
Details
To set counter type for software counter 4 on the Counter Check screen.
Use case
Upon user/dealer's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 999
0: Not registered
Default value
Refer to the specification of counter display because it differs according
to the model or the location.
8
Service Mode > COPIER > OPTION > USER
8
Service Mode > COPIER > OPTION > USER
COPIER> OPTION> USER
COUNTER5
Setting of software counter 5
Details
To set counter type for software counter 5 on the Counter Check screen.
Use case
Upon user/dealer's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 999
0: Not registered
Default value
0
COUNTER6
Setting of software counter 6
Details
To set counter type for software counter 6 on the Counter Check screen.
Use case
Upon user/dealer's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 999
0: Not registered
Default value
0
CNT-SW
Set default dspl items on charge counter
Details
To set default display items of the charge counter on the Counter Check
screen.
Use case
Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 3
0: Conventional method (type 1), 1: New method (type 2), 2: New
method (type 3), 3: New method (type 4)
Default value
0
Related service mode
COPIER> OPTION> FNC-SW> CONFIG
CONTROL
Charge setting of PDL job
Details
To set charge count transmission of PDL job to the connecting charging
management device (coin manager or non-Canon-made control card).
Use case
Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 2
0: Output is available without control card. Not counted.
1: Output is available at insertion of the card. Not counted.
2: Output is available at insertion of the card. Counted.
Default value
0
Related service mode
COPIER > OPTION > ACC > COIN
8-105
8-105
Advertisement
Table of Contents
Troubleshooting
