Canon imageRUNNER C1335 Series Service Manual page 418

Error Detail
Item
code Code
E240 0000 Title Controller communication error
Description A sequence error with the controller occurred.
Remedy [Related parts]
• Flexible Cable between the DC Controller PCB (UN04/J112) and the
Main Controller PCB (UN81/J7001) (Unit of replacement: CABLE, FLAT)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER
PCB ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Perform the following in the order while checking whether the
error is cleared.
1. Check the harness between the DC Controller PCB and the Main
Controller PCB.
2. Turn ON the power, and check if the initialization is executed at startup.
2-1. If the initialization is not executed, replace the DC Controller PCB.
2-2. If the initialization is executed, replace the Main Controller PCB.
E240 0005 Title Controller communication error
Description A sequence error with the controller occurred.
Remedy [Related parts]
• Flexible Cable between the DC Controller PCB (UN04/J112) and the
Main Controller PCB (UN81/J7001) (Unit of replacement: CABLE, FLAT)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER
PCB ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Perform the following in the order while checking whether the
error is cleared.
1. Check the harness between the DC Controller PCB and the Main
Controller PCB.
2. Turn ON the power, and check if the initialization is executed at startup.
2-1. If the initialization is not executed, replace the DC Controller PCB.
2-2. If the initialization is executed, replace the Main Controller PCB.
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7 Error•Jam•Alarm > Error Code > Error Code Details
Error Detail
Item
code Code
E240 0D00 Title Controller communication error
Description A sequence error with the controller occurred.
Remedy [Related parts]
• Flexible Cable between the DC Controller PCB (UN04/J112) and the
Main Controller PCB (UN81/J7001) (Unit of replacement: CABLE, FLAT)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER
PCB ASSEMBLY)
• Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER
PCB ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no
bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Perform the following in the order while checking whether the
error is cleared.
1. Check the harness between the DC Controller PCB and the Main
Controller PCB.
2. Turn ON the power, and check if the initialization is executed at startup.
2-1. If the initialization is not executed, replace the DC Controller PCB.
2-2. If the initialization is executed, replace the Main Controller PCB.
E246 0001 Title System error
Description System error
Remedy Contact to the sales company.
E246 0002 Title System error
Description System error
Remedy Contact to the sales company.
E246 0003 Title System error
Description System error
Remedy Contact to the sales company.
E246 0005 Title System error
Description System error
Remedy Contact to the sales company.
E247 0001 Title System error
Description System error
Remedy Contact to the sales company.
E247 0002 Title System error
Description System error
Remedy Contact to the sales company.
E247 0003 Title System error
Description System error
Remedy Contact to the sales company.
7-47
Description
7-47