Canon imageRUNNER C1335 Series Service Manual page 521

OPTION
■ BODY
COPIER> OPTION> BODY
DFDST-L1 DADF mode dust dtct level adj: ppr intvl
Details To adjust dust detection level with dust detection correction control that
is executed at paper interval in DADF mode.
Reduce the value in the case of frequent display of cleaning instruction
at the time of dust detection. As the value is smaller, the dust is less
detected.
Increase the value when black/white lines appear. As the value is larger,
the small dust is more likely detected.
Use case • When black/white line occurs due to dust
• Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Caution When increasing the value too much, the cleaning instruction screen
may appear too often since even small dust that will not be appeared on
the image can be detected.
When decreasing the value too much, lines may appear on the image.
Display/adj/set range 0 to 255
0 to 84
85 to 169
170 to 254
255
Default value 200
Supplement/memo Lines may appear on the image if there is dust. With dust detection
correction control, the image is corrected to prevent lines once dust is
detected.
To turn OFF the control, make the following selection: Settings/
Registration> Function Settings> Common> Scan Settings> Removal of
Soiled Lines, and set the item to "OFF".
JM-ERR-R Set of error display of 0071 jam (RCON)
Details To set whether to display "0071" jam as the error "E996-0071".
In the case of a jam, the target log will be lost, so that it may not be able
to be checked.
When 1 is set, it is handled as an error so that the log which has been
backed up can be obtained.
Use case When checking the occurrence of 0071 jam
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range 0 to 1
0: Display as a jam, 1: Display as an error
Default value 0
Related service mode COPIER> OPTION> FNC-SW> JM-ERR-D
8
Service Mode > COPIER > OPTION > BODY
: Weakest
: Weak
: Moderate
: Strong
8 Service Mode > COPIER > OPTION > BODY
COPIER> OPTION> BODY
SIZE-LC Setting of paper size configuration
Details To set the paper size configuration. At installation in areas other than
Japan, perform the following procedure to match the setting information
with that of the location.
Use case • At installation
• Upon user's request
Adj/set/operate 1) Enter the setting value under SIZE-LC, and then press Start key.
method 2) Execute COPIER> FUNCTION> CLEAR> ALL.
3) Turn OFF/ON the main power switch.
Caution Since COPIER> FUNCTION> CLEAR> ALL is executed when changing
the location, the setting information of user mode, service mode, etc. is
initialized. The setting information of this item is not initialized.
Display/adj/set range 1 to 4
1: AB configuration, 2: Inch configuration, 3: A configuration, 4: AB/Inch
configuration
Related service mode COPIER> FUNCTION> CLEAR> ALL
MIBCOUNT Scope range set of Charge Counter MIB
Details To set the range of counter information that can be obtained as MIB
(Management Information Base).
Use case For customization
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: All charge counters are obtained
1: Only displayed counter* is obtained
2: All charge counters are not obtained
* : Counter specified by the following: COPIER> OPTION> USER>
COUNTER 1 to 6
Default value 0
Related service mode COPIER> OPTION> USER> COUNTER1- 6
NS-CMD5 Limit CRAM-MD5 auth method at SMTP auth
Details To restrict use of CRAM-MD5 authentication method at the time of SMTP
authentication.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: SMTP server-dependent, 1: Not used
Default value 0
Supplement/memo SMTP authentication: Protocol in which user authentication function is
added to SMTP, which is the protocol to be used for e-mail transmission.
At the time of e-mail transmission, this protocol executes authentication
of the user account and the password between the SMTP server and the
user to approve e-mail transmission only when it's authenticated.
8-82
8-82