Canon imageRUNNER C1335 Series Service Manual page 396

Error Detail
Item
code Code
E100 0001 Title BD error
Description The BD lock was unlocked although it had been locked once.
Remedy [Related parts]
• Front Cover/Right Cover
• Interlock Switch 1 and 2 (SW02 and SW03/J24/1-pin and 2-pin) (Unit of
replacement: COVER, INNER, FRONT, RIGHT)
• Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/
Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER
SCANNER)
• Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/
M/C/Bk Laser Driver PCB (UN05/J201) (Unit of replacement: CABLE, FLAT)
• Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER
SCANNER ASSEMBLY)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB
ASSEMBLY)
• Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER
PCB ASSEMBLY)
• Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER
SUPPLY ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no bent
pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
E102 0001 Title EEPROM error
Description An error has occurred in EEPROM of the Laser Scanner.
Remedy [Related parts]
• Laser Scanner Unit (Unit of replacement: LASER SCANNER ASSEMBLY)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB
ASSEMBLY)
• Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/
Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER
SCANNER)
• Interlock Switch 1 and 2 (SW02 and SW03/J24/pin 1 and 2) (Unit of
replacement: COVER, INNER, FRONT, RIGHT)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no bent
pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
[Caution] After replacing the related parts, execute "Settings/Registration>
Adjustment/Maintenance> Auto Correct Color Mismatch".
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7 Error•Jam•Alarm > Error Code > Error Code Details
Error Detail
Item
code Code
E110 0001 Title Scanner Motor error
Description The speed was not locked by FG control within 5.5 sec after startup of
Scanner Motor.
Remedy [Related parts]
• Front Cover/Right Cover
• Interlock Switch 1 and 2 (SW02 and SW03/J24/1-pin and 2-pin) (Unit of
replacement: COVER, INNER, FRONT, RIGHT)
• Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/
Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER
SCANNER)
• Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/
M/C/Bk Laser Driver PCB (UN05/J201) (Unit of replacement: CABLE, FLAT)
• Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER
SCANNER ASSEMBLY)
• DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB
ASSEMBLY)
• Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER
PCB ASSEMBLY)
• Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER
SUPPLY ASSEMBLY)
[Points to note at work] When checking the harness/cable or connector,
perform the following work.
1. Disconnect and then connect the connector to check that there is no bent
pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
7-25
Description
7-25