Table 3-10 Parameters For The Addpart Command - Cisco MGX 8850 (PXM1E/PXM45) Configuration Manual

General PXM1E Configuration Procedures

Table 3-10 Parameters for the addpart Command

Parameter
ifNum
partId
ctrlrId
egrminbw
egrmaxbw
ingminbw
ingmaxbw
minVpi
maxVpi
minVci
maxVci
Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, Cisco MGX 8830, and Cisco MGX 8880 Configuration Guide
3-50
Description
Interface number or port number. This number identifies the port this resource partition
configures. Enter the interface number that was assigned to the port when it was
configured (see the "Adding ATM
Partition identification number. Enter a number in the range of 1 to 20. On an PXM1E
card, this number must be the same for all ports that use the same controller type. For
example, if you assign the number 2 to the PNNI controller on any port, the partition
ID for the PNNI controller on all other ports must be set to 2.
Controller identification number. Enter the number 2 to specify the PNNI controller.
For more information, refer to
"Configuring General Switch Features."
Egress minimum bandwidth. Enter the minimum percentage of the outgoing port
bandwidth that you want assigned to the specified controller. One percent is equal
to .0001 units. For example, an <egrminbw> of 250000 = 25%. The sum of the
minimum egress bandwidth settings for PNNI must be 100% or less, and must be less
than the sum of the egrmaxbw settings.
Egress maximum bandwidth. Enter the maximum percentage of the outgoing port
bandwidth that you want assigned to the controller. One percent is equal to .0001 units.
For example, an <egrmaxbw> of 1000000 = 100%. The sum of the maximum egress
bandwidth settings for PNNI can exceed 100%, and must be more than the sum of the
egrminbw settings. Available bandwidth above the minimum bandwidth settings is
allocated to the operating controllers on a first-requested, first-served basis until the
maximum bandwidth setting is met or there is insufficient bandwidth to meet the
request.
Ingress minimum bandwidth. Enter the minimum percentage of the incoming port
bandwidth that you want assigned to the controller. One percent is equal to .0001 units.
For example, an <ingminbw> of 500000 = 50%. The sum of the minimum ingress
bandwidth settings for PNNI must be 100% or less, and must be less than the sum of
the ingmaxbw settings.
Ingress maximum bandwidth. Enter the maximum percentage of the incoming port
bandwidth that you want assigned to the controller. One percent is equal to .0001 units.
For example, an <ingmaxbw> of 750000 = 75%. The sum of the maximum ingress
bandwidth settings for PNNI can exceed 100%, and must be more than the sum of the
ingminbw settings. Available bandwidth above the minimum bandwidth settings is
allocated to the operating controllers on a first-request, first-served basis until the
maximum bandwidth setting is met or there is insufficient bandwidth to meet the
request.
Minimum VPI. For NNI, the range is 0-4095. For UNI, the range is 0-255.
Maximum VPI in the range 0-4095 for an NNI. For a UNI, the range is 0-255. The
maxvpi cannot be less than the minvpi.
The minimum VCI has a range of 1-65535.
Maximum VPI in the range 0-4095 for an NNI. For a UNI, the range is 0-255. The
maxvpi cannot be less than the minvpi.
Chapter 3 Provisioning PXM1E Communication Links
Ports" section earlier in this chapter).
"Adding the PNNI Controller" in
Release 5.0.10, OL-3845-01 Rev. B0, August 16, 2004
Chapter 2,