Cisco MGX 8850 (PXM1E/PXM45) Configuration Manual page 40

Documentation
Table 3 Descriptions of Technical Manuals and Release Notes for Cisco Multiservice Switch Products (continued)
Document Title
Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, Cisco
MGX 8830, and Cisco MGX 8880 Hardware Installation
Guide, Releases 2 Through 5
OL-4545-01
Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, Cisco
MGX 8830, and Cisco MGX 8880 Configuration Guide,
Release 5
OL-4546-01
Cisco MGX 8850 (PXM45/PXM1E), Cisco MGX 8950, Cisco
MGX 8830, and Cisco MGX 8880 Command Reference,
Release 5
OL-4547-01
Cisco MGX 8850 Edge Concentrator Installation and
Configuration, Release 1.1.3
DOC-7811223=
Cisco MGX 8850 Multiservice Switch Overview, Release 1.1.3
OL-1154-01
Cisco MGX and Service Expansion Shelf Error Messages,
Release 5
OL-4553-01
Cisco MGX Route Processor Module (RPM-XF) Installation
and Configuration Guide, Release 4
OL-5087-01
Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, Cisco MGX 8830, and Cisco MGX 8880 Configuration Guide
xl
Description
Describes how to install the Cisco MGX 8950, the
Cisco MGX 8850 (PXM1E/PXM45), and the
Cisco MGX 8830 switches. Also describes how to install the
MGX 8880 Media Gateway. This document explains what
each switch does and covers site preparation, grounding,
safety, card installation, and cabling. The Cisco MGX 8850
switch uses either a PXM45 or a PXM1E controller card and
provides support for both serial bus-based and cell bus-based
service modules. The Cisco MGX 8830 switch uses a
PXM1E controller card and supports cell bus-based service
modules. The Cisco MGX 8950 supports only serial
bus-based service modules. The Cisco MGX 8880 uses a
PXM45/C controller card, and supports only serial bus-based
service modules. This hardware installation guide replaces
all previous hardware guides for these switches.
Describes how to configure the Cisco MGX 8880 Media
Gateway. Also describes how to configure Cisco MGX 8850
(PXM1E), Cisco MGX 8850 (PXM45), and Cisco
MGX 8830 switches to operate as ATM edge switches and
the Cisco MGX 8950 switch to operate as a core switch. This
guide also provides some operation and maintenance
procedures.
Describes the PXM commands that are available in the CLI
of the Cisco MGX 8850 (PXM45), Cisco MGX 8850
(PXM1E), Cisco MGX 8950, and Cisco MGX 8830 switches.
Also describes the PXM commands that are available in the
CLI of the Cisco MGX 8880 Media Gateway.
Provides installation instructions for the Cisco MGX 8850
(PXM1) edge concentrator.
Describes the system components and function of the
Cisco MGX 8850 (PXM1) edge concentrator.
Provides error message descriptions and recovery
procedures.
Describes how to install and configure the Cisco MGX Route
Processor Module (RPM-XF) in the Cisco MGX 8850
(PXM45) and Cisco MGX 8950 switch. Also provides site
preparation procedures, troubleshooting procedures,
maintenance procedures, cable and connector specifications,
and basic Cisco IOS configuration information.
Release 5.0.10, OL-3845-01 Rev. B0, August 16, 2004
About This Guide