Cisco 880 Series Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 880 Series
  6. Installation manual
Cisco 880 Series Installation Manual

Cisco 880 Series Installation Manual

Cisco systems integrated services router installation guide
Hide thumbs Also See for 880 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual, Manual
Installing Memory and Power Over Ethernet in
Cisco 880 Series and Cisco 890 Series Integrated
Services Routers
Warning
Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Statement 1
This document describes how to install memory and Power over Ethernet (PoE) in a Cisco 880 series
and Cisco 890 series Integrated Services Routers (ISRs). It contains the following sections:
•
•
•
•
•
Memory and PoE are the only upgradable options in the Cisco 880 series and Cisco 890 series ISRs. Do
Note
not remove or install any other internal module.

Safety Warnings

Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning
Statement 1001
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Safety Warnings
Installing Main Memory
Installing Power Over Ethernet
Opening the Chassis
Closing the Chassis

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 880 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Cisco 880 Series

Summary of Contents for Cisco 880 Series

  • Page 1: Safety Warnings

    • • Opening the Chassis • Closing the Chassis Memory and PoE are the only upgradable options in the Cisco 880 series and Cisco 890 series ISRs. Do Note not remove or install any other internal module. Safety Warnings Warning This equipment must be grounded.

  • Page 2: Installation Procedure

    Open the chassis according to the instructions in the Step 2 Locate the DIMM socket on the system board. See Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers Items and Their Quantities Shipped with a DIMM Unit Quantity Figure 1 “Opening the Chassis”...
  • Page 3 Remove any existing DIMM by gently pulling the spring-loaded clips on the end of the socket far enough Step 3 to release the DIMM, then gently pulling the DIMM up and away from the socket. See Figure Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers OL-16194-01...
  • Page 4 Step 5 spring-loaded clips. Close the chassis according to the instructions in Step 6 Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers “Closing the Chassis” section on page DIMM socket Spring-loaded clips...

  • Page 5: Installing Power Over Ethernet

    PoE card. Failure to do so may result in damage to the PoE card or to the router. Open the chassis according to the instructions in Step 1 Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers OL-16194-01 Items and Their Quantities Shipped with a PoE Module Quantity “Opening the Chassis”...
  • Page 6 Standoff holes with star pattern Remove the screw from the third standoff hole. Step 3 Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers Figure 4 for the location of the PoE...
  • Page 7 Standoff hole without star pattern Standoff holes with star pattern Metal standoffs with two notches Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers OL-16194-01 Installing the Power over Ethernet Card Installing Power Over Ethernet Figure 5.

  • Page 8: Opening The Chassis

    Cisco 880 series ISRs. Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers Closing the Chassis, page 10), and then connect the PoE power supply to an AC Figure 6 shows the location of the screws.
  • Page 9 The front end of the chassis cover will remain attached to the chassis. Figure 7 shows how to open the chassis. Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers OL-16194-01...

  • Page 10: Closing The Chassis

    During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94 Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers OL-16194-01...
  • Page 11 CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the IronPort logo, Laser Link, LightStream,...
  • Page 12 Closing the Chassis © 2009 Cisco Systems, Inc. All rights reserved. Installing Memory and Power Over Ethernet in Cisco 880 Series and Cisco 890 Series Integrated Services Routers OL-16194-01...

Table of Contents

Save PDF