E3-01 (Motor 2 Control Mode) Dependent Parameters - YASKAWA A1000 Technical Manual

No. Name
o1-03 Digital Operator Display Selection
o1-04 V/f Pattern Display Unit
<6> Default setting is determined by parameter o2-04, Drive Model Selection.
<14> Default setting value is dependent on the motor code set to parameter E5-01.
<18> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<41> This default value is a calculated as a percentage of the maximum output frequency.
<55> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percent (0.0 to 100.0%) instead of in Hz.
<56> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percent (0.0 to 40.0%) instead of in Hz.
<57> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percent (-100.0 to 100.0%) instead of in Hz.
 E3-01 (Motor 2 Control Mode) Dependent Parameters
Table B.4 E3-01 (Motor 2 Control Mode) Dependent Parameters and Default Values
No. Name
C3-21 Motor 2 Slip Compensation Gain
C3-22 Motor 2 Slip Compensation Primary Delay Time
C5-21 Motor 2 ASR Proportional Gain 1
C5-22 Motor 2 ASR Integral Time 1
C5-23 Motor 2 ASR Proportional Gain 2
C5-24 Motor 2 ASR Integral Time 2
C5-26 Motor 2 Carrier Frequency Selection
E3-04 Motor 2 Maximum Output Frequency
E3-05 Motor 2 Maximum Output Voltage
E3-06 Motor 2 Base Frequency
E3-07 Motor 2 Mid Output Frequency
E3-08 Motor 2 Mid Output Frequency Voltage
E3-09 Motor 2 Minimum Output Frequency
E3-10 Motor 2 Minimum Output Voltage
E3-04 to The default setting of these parameters depends on the control mode but also on the drive capacity They are equivalent to the motor 1 settings. Refer to
E3-10 Values on page 522.
<9> Default setting is determined by the drive model (o2-04) and duty selection (C6-01).
<18> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
B.4 Control Mode Dependent Parameter Default Values
Setting Range
0 to 3
0 to 1
Setting Range
0.0 to 2.5
0 to 10000
0.00 to 300.00
0.000 to 10.000
0.00 to 300.00
0.000 to 10.000
1 to F
40.0 to 400.0
0.0 to 255.0
<18>
0.0 to 400.0
0.0 to 400.0
0.0 to 255.0
<18>
0.0 to 400.0
0.0 to 255.0
<18>
Control Modes (A1-02)
Resolution
OLV/PM (5)
– 0
– –
Resolution
V/f (0)
0.1 0.0
1 ms 2000
0.01 –
0.001 s –
0.01 –
0.001 s –
– 7
<9>
0.1 Hz 60.0
0.1 V 200.0
0.1 Hz 60.0
0.1 Hz 3.0
0.1 V 15.0
0.1 Hz 1.5
0.1 V 9.0
AOLV/PM (6) CLV/PM (7)
1 1
1 1
Control Modes (E3-01)
V/f w/PG (1) OLV (2) CLV (3)
– 1.0
– 200
0.20 – 20.00
0.200 – 0.500
0.02 – 20.00
0.050 – 0.500
7 7 7
<9> <9>
60.0 60.0 60.0
200.0 200.0 200.0
60.0 60.0 60.0
3.0 3.0
15.0 11.0
1.5 0.5
9.0 2.0
V/f Pattern Default
1.0
–
<9>
0.0
0.0
0.0
0.0
B
521