YASKAWA A1000 Technical Manual page 490

B.3 Parameter Table
No.(Addr.) Name
H3-08
(416H)
Terminal A3 Bias Setting
H3-09 Terminal A2 Signal Level
(417H) Selection
H3-10
Terminal A2 Function Selection
(418H)
H3-11
(419H)
Terminal A2 Gain Setting
H3-12
(41AH)
Terminal A2 Bias Setting
H3-13
Analog Input Filter Time Constant
(41BH)
H3-14 Analog Input Terminal Enable
(41CH) Selection
H3-16
Terminal A1 Offset
(2F0H)
H3-17
Terminal A2 Offset
(2F1H)
H3-18
Terminal A3 Offset
(2F2H)
Setting Function
0 Frequency Bias
1 Frequency Gain
2 Auxiliary Frequency Reference 1
3 Auxiliary Frequency Reference 2
4 Output Voltage Bias
5 Accel/Decel Time Gain
6 DC Injection Braking Current
7 Overtorque/Undertorque Detection Level
8 Stall Prevention Level During Run
490
All Modes
Sets the level of the input value selected in H3-06 when 0 V is input at terminal A3.
All Modes
0: 0 to 10 V
1: -10 to 10 V
2: 4 to 20 mA
3: 0 to 20 mA
Note: Use DIP switch S1 to set input terminal A2 for a current or a voltage input signal.
All Modes
Sets the function of terminal A2.
All Modes
Sets the level of the input value selected in H3-10 when 10 V (20 mA) is input at terminal A2.
All Modes
Sets the level of the input value selected in H3-10 when 0 V (0 or 4 mA) is input at terminal A2.
All Modes
Sets a primary delay filter time constant for terminals A1, A2, and A3. Used for noise filtering.
All Modes
Determines which of the analog input terminals will be enabled or disabled when a digital input
programmed for "Analog input enable" (H1- = C) is activated. The terminals other than the
one set as the target are not influenced by input signals.
1: Terminal A1 only
2: Terminal A2 only
3: Terminals A1 and A2 only
4: Terminal A3 only
5: Terminals A1 and A3
6: Terminals A2 and A3
7: All terminals enabled
All Modes
Adds an offset when the analog signal to terminal A1 is at 0 V.
All Modes
Adds an offset when the analog signal to terminal A2 is at 0 V.
All Modes
Adds an offset when the analog signal to terminal A3 is at 0 V.
H3 Multi-Function Analog Input Settings
All Modes
10 V = E1-04 (maximum output frequency)
All Modes
0 to 10 V signal allows a setting of 0 to 100%. -10 to 0 V signal allows a setting of -100 to 0%.
All Modes
10 V = E1-04 (maximum output frequency)
All Modes
10 V = E1-04 (maximum output frequency)
V/f V/f w/PG
OLV/PM AOLV/PM
10 V = E1-05 (motor rated voltage)
All Modes
10 V = 100%
V/f V/f w/PG
OLV/PM AOLV/PM
10 V = Drive rated current
All Modes
10 V = Drive rated current (V/f, V/fw/PG)
10 V = Motor rated torque (OLV, CLV, OLV/PM, AOLV/PM, CLV/PM)
V/f V/f w/PG
OLV/PM AOLV/PM
10 V = Drive rated current
YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
Description
Description (For when output is 100%)
OLV CLV
CLV/PM
OLV CLV
CLV/PM
OLV
CLV
CLV/PM
Setting Page
Default: 0.0%
Min: -999.9% 258
Max: 999.9%
Default: 2
Min: 0 258
Max: 3
Default: 0
Min: 0 259
Max: 32
Default: 100.0%
Min: -999.9% 259
Max: 999.9%
Default: 0.0%
Min: -999.9% 259
Max: 999.9%
Default: 0.03 s
Min: 0.00 s 259
Max: 2.00 s
Default: 7
Min: 1 259
Max: 7
Default: 0
Min: -500 260
Max: 500
Default: 0
Min: -500 260
Max: 500
Default: 0
Min: -500 260
Max: 500
Page
260
260
260
260
260
261
261
261
261