Applicable Documentation - YASKAWA A1000 Technical Manual

i.1 Preface
i.1 Preface
YASKAWA manufactures products used as components in a wide variety of industrial systems and equipment. The
selection and application of YASKAWA products remain the responsibility of the equipment manufacturer or end user.
YASKAWA accepts no responsibility for the way its products are incorporated into the final system design. Under no
circumstances should any YASKAWA product be incorporated into any product or design as the exclusive or sole safety
control. Without exception, all controls should be designed to detect faults dynamically and fail safely under all
circumstances. All systems or equipment designed to incorporate a product manufactured by YASKAWA must be
supplied to the end user with appropriate warnings and instructions as to the safe use and operation of that part. Any
warnings provided by YASKAWA must be promptly provided to the end user. YASKAWA offers an express warranty
only as to the quality of its products in conforming to standards and specifications published in the YASKAWA manual.
NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS OFFERED. YASKAWA assumes no liability for any personal
injury, property damage, losses, or claims arising from misapplication of its products.
This manual is designed to ensure correct and suitable application of Variable A1000-Series Drives. Read this manual
before attempting to install, operate, maintain, or inspect a drive and keep it in a safe, convenient location for future
reference. Be sure you understand all precautions and safety information before attempting application.
 Applicable Documentation
The following manuals are available for A1000 series drives:
ALM
DIGITAL OPERATOR JVOP-180
F1 F2
LO
ESC
RE
RESET ENTER
RUN STOP
CIMR-AA2A0021FAA
200V 3Phase 5.5kW/3.7kW
S/N:
WARNING AVERTISSMENT NPJT31470-1
Risk of electric shock. Risque de décharge électrique.
Read manual before installing. Lire le manuel avant l'installation.
● ●
Wait 5 minutes for capacitor ● ● Attendre 5 minutes après la coupure
discharge after disconnecting de l'alimentation, pour permettre
power supply. la décharge des condensateurs.
To conform to requirements, Pour répondre aux exigences , s
● make sure to ground the supply ●
assurer que le neutre soit relié
neutral for 400V class. à la terre, pour la série 400V.
After opening the manual switch ● Après avoir déconnécte la protection
between the drive and motor, ● entre le driver et le moteur, veuillez
please wait 5 minutes before patienter 5 minutes avain d'effectuer
inspecting, performing
une opération de montage ou de
maintenance or wiring the drive. câblage du variateur.
Hot surfaces Surfaces Chaudes
Top and Side surfaces may ● ● Dessus et cotés du boitier Peuvent
become hot. Do not touch. devenir chaud. Ne Pas toucher.
危 険
けが．感電のおそれがあります。
● ● 据え付け、 運転の前には必ず取扱説明書を読むこと。
● ● 通電中および電源遮断後5分以内はフロントカバー
を外さない事。
● 400V級インバータの場合は、電源の中性点が接地
● されていることを確認すること。( 対応）
● 保守・点検、配線を行う場合は、出力側開閉器を
● 遮断後5分待って実施してください。
高温注意
インバータ上部、両側面は高温になります。
● 触らないでください。
●
 Symbols
Note: Indicates a supplement or precaution that does not cause drive damage.
TERMS TERMS TERMS
: Indicates a term or definition used in this manual.
 Terms and Abbreviations
• Drive: YASKAWA A1000 Series Drive
TERMS TERMS TERMS
• V/f: V/f Control
• V/f w/PG: V/f Control with PG
• OLV: Open Loop Vector Control
• CLV: Closed Loop Vector Control
• OLV/PM: Open Loop Vector Control for PM
• AOLV/PM: Advanced Open Loop Vector Control for PM
• CLV/PM: Closed Loop Vector Control for PM
• PM motor: Permanent Magnet Synchronous motor (an abbreviation for IPM motor or SPM motor)
• IPM motor: Interior Permanent Magnet Motor (such as YASKAWA's SSR1 Series and SST4 Series motors)
• SPM motor: Surface mounted Permanent Magnet Motor (such as YASKAWA's SMRA Series motors)
 Trademarks
• CANopen is a trademark of CAN in Automation (CiA).
• CC-Link is a trademark of CC-Link Partner Association (CLPA).
• DeviceNet is a trademark of Open DeviceNet Vendor Association, Inc. (ODVA).
• PROFIBUS-DP is a trademark of PROFIBUS International (PI).
• MECHATROLINK-I, MECHATROLINK-II, and MECHATROLINK-III are a trademark of MECHATROLINK
Members Association (MMA).
• LONWORKS is a trademark of ECHELON USA.
• Modbus TCP/IP is a trademark of Modbus-IDA.
• EtherNet/IP is a trademark of the ODVA.
• Other companies and product names mentioned in this manual are trademarks of those companies.
16
A1000 Series AC Drive Quick Start Guide
This guide is packaged together with the product. It contains basic information on safety precautions, model list, and wiring. It is
meant to get the drive ready for a trial run with the application and for basic operation.
A1000 Series AC Drive Technical Manual (this book)
This manual is included on the CD-ROM packaged with the product (YASKAWA AC Drive Manuals, TOBC C710616 21). The
manual contains information required to install and wire the drive, in addition to an overview of fault diagnostics, maintenance
safety, and parameter settings. Contact a YASKAWA representative to obtain the manual. The manual is also available for
download on our documentation website, e-mechatronics.com.
YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual