YASKAWA A1000 Technical Manual page 486

B.3 Parameter Table
H1-
Function
Setting
7A KEB Ride-Thru 2 (N.C.)
7B KEB Ride-Thru 2 (N.O.)
7C Short Circuit Braking (N.O.)
7D Short Circuit Braking (N.C.)
7E Forward/Reverse Detection
7F Bi-Directional PID Output Selection
90 to 97 DriveWorksEZ Digital Inputs 1 to 8
9F DriveWorksEZ Disable

H2: Multi-Function Digital Outputs
No.(Addr.) Name
H2-01 Terminal M1-M2 Function
(40BH) Selection (Relay)
H2-02 Terminal M3-M4 Function
(40CH) Selection (Relay)
H2-03 Terminal M5-M6 Function
(40DH) Selection (Relay)
H2-06
Watt Hour Output Unit Selection
(437H)
H2-07
Memobus Regs1 Address Select
(B3AH)
H2-08
Memobus Regs1 Bit Select
(B3BH)
H2-09
Memobus Regs2 Address Select
(B3CH)
H2-10
Memobus Regs2 Bit Select
(B3DH)
486
H1 Multi-Function Digital Input Selections
All Modes
Open: KEB Ride-Thru 2 enabled. Drive disregards L2-29 and performs Single Drive KEB Ride-Thru 2.
All Modes
Closed: KEB Ride-Thru 2 enabled. Drive disregards L2-29 and performs Single Drive KEB Ride-Thru 2.
V/f V/f w/PG
OLV/PM AOLV/PM
Closed: Short Circuit Braking enabled
V/f V/f w/PG
OLV/PM AOLV/PM
Open: Short Circuit Braking enabled
V/f V/f w/PG
OLV/PM AOLV/PM
Open: Forward motor operation is detected.
Closed: Reverse motor operation is detected.
All Modes
Open: Bi-directional output is disabled.
Closed: Bi-directional output is enabled.
All Modes
Reserved for DWEZ input functions
All Modes
Open: DWEZ enabled
Closed: DWEZ disabled
All Modes
Refer to H2 Multi-Function Digital Output Settings on page
values.
All Modes
Sets the output units for the watt hours when Watt Hour Pulse Output is selected as the digital
output (H2-01, H2-02, or H2-03 = 39). Outputs a 200 ms pulse signal when the watt-hour
counter increases by the units selected.
0: 0.1 kWh units
1: 1 kWh units
2: 10 kWh units
3: 100 kWh units
4: 1000 kWh units
All Modes
Sets the addresses of the MEMOBUS/Modbus registers from which data will be sent to contact
outputs 62 and 162.
Note: This parameter is not available with models CIMR-A4A0930 and 4A1200.
All Modes
Sets the bits for the MEMOBUS/Modbus registers from which data will be sent to contact
outputs 62 and 162.
Note: This parameter is not available with models CIMR-A4A0930 and 4A1200.
All Modes
Sets the addresses of the MEMOBUS/Modbus registers from which data will be sent to contact
outputs 63 and 163.
Note: This parameter is not available with models CIMR-A4A0930 and 4A1200.
All Modes
Sets the bits for the MEMOBUS/Modbus registers from which data will be sent to contact
outputs 63 and 163.
Note: This parameter is not available with models CIMR-A4A0930 and 4A1200.
YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
Description
OLV CLV
CLV/PM
OLV
CLV
CLV/PM
OLV CLV
CLV/PM
Description
487 for a description of setting
Page
245
245
245
245
245
245
245
245
Setting Page
Default: 0
Min: 0 246
Max: 192
Default: 1
Min: 0 246
Max: 192
Default: 2
Min: 0 246
Max: 192
Default: 0
Min: 0 256
Max: 4
Default: 1
Min: 1 256
Max: 1FFF
Default: 0
Min: 0 256
Max: FFFF
Default: 1
Min: 1 256
Max: 1FFF
Default: 0
Min: 0 256
Max: FFFF