E.3 User Setting Table - YASKAWA A1000 Technical Manual

E.3 User Setting Table

E.3 User Setting Table
Use the Verify Menu to see which parameters have been changed from their original default settings.
• The diamond below the parameter number indicates that the parameter setting can be changed during run.
• Parameter names in boldface type are included in the Setup Group of parameters which can be set by A1-06 = 0).
No.
A1-00 Language Selection
A1-01 Access Level Selection
A1-02 Control Method Selection
A1-03 Initialize Parameters
A1-04 Password
A1-05 Password Setting
A1-06 Application Preset
A1-07 DriveWorksEZ Function Selection
A2-01 to
User Parameters 1 to 32
A2-32
A2-33 User Parameter Automatic Selection
b1-01 Frequency Reference Selection 1
b1-02 Run Command Selection 1
b1-03 Stopping Method Selection
b1-04 Reverse Operation Selection
b1-05 Action Selection below Minimum Output Frequency
b1-06 Digital Input Reading
b1-07 LOCAL/REMOTE Run Selection
b1-08 Run Command Selection while in Programming Mode
b1-14 Phase Order Selection
b1-15 Frequency Reference Selection 2
b1-16 Run Command Selection 2
b1-17 Run Command at Power Up
b1-21 Start Condition Selection at Closed Loop Vector Control
<1>
b2-01 DC Injection Braking Start Frequency
b2-02 DC Injection Braking Current
b2-03 DC Injection Braking Time at Start
b2-04 DC Injection Braking Time at Stop
b2-08 Magnetic Flux Compensation Value
b2-12 Short Circuit Brake Time at Start
b2-13 Short Circuit Brake Time at Stop
b2-18 Short Circuit Braking Current
b3-01 Speed Search Selection at Start
b3-02 Speed Search Deactivation Current
b3-03 Speed Search Deceleration Time
b3-04 V/f Gain during Speed Search
b3-05 Speed Search Delay Time
b3-06 Output Current 1 during Speed Search
Output Current 2 during Speed Search (Speed Estimation
b3-07
Type)
Current Control Gain during Speed Search (Speed
b3-08
Estimation Type)
Current Control Integral Time during Speed Search (Speed
b3-09
Estimation Type)
b3-10 Speed Search Detection Compensation Gain
b3-12 Minimum Current Detection Level during Speed Search
b3-14 Bi-Directional Speed Search Selection
b3-17 Speed Search Restart Current Level
b3-18 Speed Search Restart Detection Time
b3-19 Number of Speed Search Restarts
b3-24 Speed Search Method Selection
b3-25 Speed Search Wait Time
b3-26 Direction Determining Level
b3-27 Start Speed Search Select
b3-29 Speed Search Induced Voltage Level
<1>
Speed Search Selection when Driving Instruction is Input
b3-33
<1>
in Uv
b4-01 Timer Function On-Delay Time
606
User
Name
Setting
No.
b4-02 Timer Function Off-Delay Time
b4-03 H2-01 ON Delay Time
<1>
b4-04 H2-01 OFF Delay Time
<1>
b4-05 H2-02 ON Delay Time
<1>
b4-06 H2-02 OFF Delay Time
<1>
b4-07 H2-03 ON Delay Time
<1>
b4-08 H2-03 OFF Delay Time
<1>
b5-01 PID Function Setting
b5-02 Proportional Gain Setting (P)
b5-03 Integral Time Setting (I)
b5-04 Integral Limit Setting
b5-05 Derivative Time (D)
b5-06 PID Output Limit
b5-07 PID Offset Adjustment
b5-08 PID Primary Delay Time Constant
b5-09 PID Output Level Selection
b5-10 PID Output Gain Setting
b5-11 PID Output Reverse Selection
b5-12 PID Feedback Loss Detection Selection
b5-13 PID Feedback Loss Detection Level
b5-14 PID Feedback Loss Detection Time
b5-15 PID Sleep Function Start Level
b5-16 PID Sleep Delay Time
b5-17 PID Accel/Decel Time
b5-18 PID Setpoint Selection
b5-19 PID Setpoint Value
b5-20 PID Setpoint Scaling
b5-34 PID Output Lower Limit
b5-35 PID Input Limit
b5-36 PID Feedback High Detection Level
b5-37 PID Feedback High Detection Time
b5-38 PID Setpoint User Display
b5-39 PID Setpoint Display Digits
b5-40 Frequency Reference Monitor Content during PID
b5-47 PID Output Reverse Selection 2
b6-01 Dwell Reference at Start
b6-02 Dwell Time at Start
b6-03 Dwell Reference at Stop
b6-04 Dwell Time at Stop
b7-01 Droop Control Gain
b7-02 Droop Control Delay Time
b7-03 Droop Control Limit Selection
b8-01 Energy Saving Control Selection
b8-02 Energy Saving Gain
b8-03 Energy Saving Control Filter Time Constant
b8-04 Energy Saving Coefficient Value
b8-05 Power Detection Filter Time
b8-06 Search Operation Voltage Limit
b8-16 Energy Saving Parameter (Ki) for PM Motors
b8-17 Energy Saving Parameter (Kt) for PM Motors
q-Axis Current Compensation Method when Output
b8-27
<1>
Voltage is Limited
b9-01 Zero Servo Gain
b9-02 Zero Servo Completion Width
C1-01 Acceleration Time 1
C1-02 Deceleration Time 1
C1-03 Acceleration Time 2
YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
User
Name
Setting