YASKAWA A1000 Technical Manual page 565

Register No.
Alarm contents 4
bit 0
bit 1
bit 2 to 5
00CAH bit 6
bit 7
bit 9
bit A
bit B to F
Alarm Contents 5
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
00CBH
bit 7
bit 8
bit 9
bit A
bit B
bit C
bit D
bit E, F
Alarm Contents 6
bit 0
bit 1
bit 2
bit 3
bit 4
00CCH
bit 5 to 6
bit 7
bit 8
bit 9 to B
bit C
bit D to F
00CDH to 00CFH Reserved
CPF Contents 1
bit 0, 1
bit 2
bit 3
bit 4, 5
bit 6
bit 7
00D0H
bit 8
bit 9, A
bit B
bit C
bit D
bit E
bit F
CPF Contents 2
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
00D1H bit 7
bit 8
bit 9
bit A
bit B
bit C
bit D
bit E
bit F
YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
Contents
Reserved
Motor Overheat 1 (PTC Input) (oH3)
Reserved
PID Feedback Loss (FbL)
PID Feedback Loss (FbH)
Drive Disabled (dnE)
PG Disconnected (PGo)
Reserved
MECHATROLINK Watchdog Timer Error (E5)
Station Address Setting Error (AEr)
MECHATROLINK Comm. Cycle Setting Error (CyC)
High Current Alarm (HCA)
Cooling Fan Maintenance Time (LT-1)
Soft Charge Bypass Relay Maintenance Time (LT-2)
Reserved
SI-S EEPROM Error (EEP)
External Fault 1 (input terminal S1) (EF1)
External Fault 2 (input terminal S2) (EF2)
Safe Disable Input (HbbF)
Safe Disable Input (Hbb)
Mechanical Weakening Detection 1 (oL5)
Mechanical Weakening Detection 2 (UL5)
Reserved
Output Voltage Detection Fault (VoF)
IGBT Maintenance Time (90%) (TrPC)
Capacitor Maintenance Time (LT-3)
IGBT Maintenance Time (50%) (LT-4)
Braking Transistor Overload Fault (boL)
Reserved
Motor Overheat (NTC Input) (oH5)
DriveWorksEZ Fault (dWAL)
Reserved
Thermistor Disconnect (THo)
Reserved
Reserved
A/D Conversion Error (CPF02)
PWM Data Fault (CPF03)
Reserved
EEPROM Memory Data Error (CPF06)
Terminal Board Connection Error (CPF07)
EEPROM Serial Communications Fault (CPF08)
Reserved
RAM Fault (CPF11)
FLASH Memory Fault (CPF12)
Watchdog Circuit Exception (CPF13)
Control Circuit Fault (CPF14)
Reserved
Clock Fault (CPF16)
Timing Fault (CPF17)
Control Circuit Fault (CPF18)
Control Circuit Fault (CPF19)
Hardware fault at power up (CPF20)
Hardware fault at communication start up (CPF21)
A/D Conversion Fault (CPF22)
PWM Feedback Fault (CPF23)
Drive Unit Signal Fault (CPF24)
Terminal board is not properly connected. (CPF25)
ASIC BB Circuit Error (CPF26)
ASIC PWM Setting Register Error (CPF27)
ASIC PWM Pattern Error (CPF28)
ASIC On-delay Error (CPF29)
ASIC BBON Error (CPF30)
ASIC Code Error (CPF31)
C.9 MEMOBUS/Modbus Data Table
C
565