E3-01 (Motor 2 Control Mode) Dependent Parameters - YASKAWA A1000 HHP Programming Manual

A.16 Control Mode Dependent Parameter Default Values
No. Name
Carrier Frequency Reduction Off Delay
L8-40
Time
o1-03 Digital Operator Display Selection
o1-04 V/f Pattern Display Unit
<1> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percentage (0.0 to 100.0%) instead of in Hz.
<2> This setting value depends on a Maximum Applicable Motor Capacity in models CIMR-Ao2A0250 to 2A0415, CIMR-Ao4A0139 to 4A1200,
A1000 HHP, and CIMR-Ao5A0099 to 5A0242: 2.00 in Open Loop Vector Control, 0.05 in Closed Loop Vector Control.
<3> This setting value depends on a Maximum Applicable Motor Capacity: 1000 s in models CIMR-Ao2A0138 to 2A0415, CIMR-Ao4A0139 to
4A1200, A1000 HHP, and CIMR-Ao5A0099 to 5A0242
<4> Default setting is dependent on parameter C6-01, Drive Duty Selection.
<5> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percentage (0.0 to 40.0%) instead of in Hz.
<6> Values shown are specific to 400 V class drives. Multiply the value by 1.4375 for 575 V class drives. Multiply the value by 1.725 for 690 V class
drives.
<7> This setting value depends on a Maximum Applicable Motor Capacity and V/f pattern selection in parameter E1-03.
<8> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percentage (-100.0 to 100.0%) instead of in Hz.
u

E3-01 (Motor 2 Control Mode) Dependent Parameters

Table A.3 E3-01 (Motor 2 Control Mode) Dependent Parameters and Default Values
No.
C3-21 Motor 2 Slip Compensation Gain
Motor 2 Slip Compensation Primary Delay
C3-22
Time
C5-21 Motor 2 ASR Proportional Gain 1
C5-22 Motor 2 ASR Integral Time 1
C5-23 Motor 2 Proportional Gain 2
C5-24 Motor 2 ASR Integral Time 2
C5-26 Motor 2 Carrier Frequency Selection
E3-04 Motor 2 Maximum Output Frequency
E3-05
Motor 2 Maximum Output Voltage
E3-06 Motor 2 Base Frequency
E3-07 Motor 2 Mid Output Frequency
E3-08
Motor 2 Mid Output Frequency Voltage
E3-09 Motor 2 Minimum Output Frequency
E3-10
Motor 2 Minimum Output Voltage
<1> Default setting is determined by parameters o2-04, Drive Model Selection, and C6-01, Drive Duty Selection.
<2> Values shown here are specific to 400 V class drives. Multiply the values by 1.4375 for 575 V class drives. Multiply the values by 1.725 for 690
V class drives.
308
Setting Range
0.00 to 2.00
Name Setting Range
0.00 to 300.00
0.000 to 10.000
0.00 to 300.00
0.000 to 10.000
40.0 to 150.0
<2>
<2>
<2>
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
Resolution
0.01 s
0 to 3 1
0 to 1 1
Resolution
0.0 to 2.5 0.1
0 to 10000 1 ms
0.01
0.001 s
0.01
0.001 s
1 to F –
0.1 Hz
0.0 to 510.0 0.2 V
0.0 to 150.0 0.1 Hz
0.0 to 150.0 0.1 Hz
0.0 to 510.0 0.2 V
0.0 to 150.0 0.1 Hz
0.0 to 510.0 0.2 V
Control Modes (A1-02)
V/f (0) V/f w/PG (1) OLV (2)
0.50 0.50 0.50
0 0
— — —
Control Modes (E3-01)
V/f (0) V/f w/PG (1) OLV (2)
0.0 – 1.0
2000 – 200
– 0.20 –
– 0.200 –
– 0.02 –
– 0.050 –
<1> <1> <1>
7 7 7
60.0 60.0 60.0
400.0 400.0 400.0
60.0 60.0 60.0
3.0 3.0 3.0
30.0 30.0 22.0
1.5 1.5 0.5
18.0 18.0 4.0
CLV (3)
0.50
0 0
0
CLV (3)
1.0
–
20.00
0.500
20.00
0.500
<1>
7
60.0
400.0
60.0
0.0
0.0
0.0
0.0