ADEMCO VISTA-120 Installation And Setup Manual
  1. Manuals
  2. Brands
  3. ADEMCO Manuals
  4. Security System
  5. VISTA-120
  6. Installation and setup manual

ADEMCO VISTA-120 Installation And Setup Manual

Partitioned security system with scheduling
Hide thumbs Also See for VISTA-120:
Table of Contents

Advertisement

Quick Links

See also: User Manual
VISTA-120
Partitioned Security System
with Scheduling
Installation and Setup Guide
®
N5944-8V1 Rev. B 6/99

Advertisement

Table of Contents
loading

Related Manuals for ADEMCO VISTA-120

Summary of Contents for ADEMCO VISTA-120

  • Page 1 VISTA-120 Partitioned Security System with Scheduling Installation and Setup Guide ® N5944-8V1 Rev. B 6/99...

  • Page 2: Thank You

    THANK YOU! For Choosing Ademco's Vista-120...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS PART 1 HARDWARE INSTALLATION PROCEDURES..1 Section 1: GENERAL DESCRIPTION ................2 Section 2: PLANNING A PARTITIONED SYSTEM............6 Theory of Partitioning ..................6 Setting up a Partitioned System................6 Common Area Logic....................7 Master Keypad Setup and Operation..............10 Section 3: FALSE ALARM REDUCTION FEATURES ..........11 Exit Error Logic ....................
  • Page 4 Section 16: FINAL POWER-UP PROCEDURE...............58 Earth Ground Considerations................58 Connecting the Transformer................58 Connecting The Battery ..................59 Polling Loop Current Drain Worksheet ............60 Auxiliary Device Current Drain Worksheet ............. 60 Section 17: ACCESS CONTROL VIA ADEMCO PASSPOINT ACM......61 –ii–...
  • Page 5 PART 2 PROGRAMMING THE SYSTEM ......65 Section 18: THE MECHANICS OF PROGRAMMING ........... 66 Using Data Field Programme Mode ..............66 System and Communication Defaults ............... 66 Entering Data Field Programme Mode ............. 66 Moving From One Page of Programming to Another........67 Viewing Data Fields ...................
  • Page 6 Section 24: DOWNLOADING ...................140 Getting On-Line with a Control Panel ............140 On-Line Control Functions ................141 Access Security ....................141 Connecting a 4100SM Module for Direct Wire Downloading ......142 Section 25: SETTING THE REAL-TIME CLOCK............143 PART 3 SYSTEM OPERATION AND TESTING....144 Section 26: SECURITY ACCESS CODES...............145 User Codes and Levels of Authority ..............

  • Page 7: List Of Figures

    LIST OF FIGURES Installing The Lock ..................11 Mounting The PC Board................11 Standard Phone Line Connections ............. 12 AC Power And Battery Connections............13 4300 Transformer Connections ..............13 Keypad Connections to Keypad Port Terminals ........14 Using a Supplementary Power Supply for Additional Keypads ....15 Zones 1-9 Wiring Connections..............

  • Page 8: Conventions Used In This Manual

    These prompts are shown in a double-line box. When programming the system, data fields are indicated by a “star” ( ) followed by the data field number. PRODUCT MODEL NUMBERS : Unless noted otherwise, references to specific model numbers represent Ademco products. –vi–...

  • Page 9: Hardware Installation Procedures

    PART 1 HARDWARE INSTALLATION PROCEDURES – 1 –...

  • Page 10: General Description

    NOTE: This manual describes features of Vista-120 with software revision "WAVIS120-14." New features included in this version are indicated by margin lines. The VISTA-120 is an 8-Partition alarm control panel that supports up to 128 zones using basic wired, polling loop, and wireless zones.
  • Page 11 32 of these zones can be used as if they were basic number across all partitions, and will only utilise wired zones, as long as they are within VISTA-120's one user "slot" in the system. Certain characteristics total capacity of 128 protection zones.
  • Page 12 Optional Output Devices (4204 Relays and Optional Keyswitch Powerline Carrier [i.e., X-10] Devices) Supports the Ademco 4146 keyswitch on any one of Accommodates the use of 32 output devices, which the system's 8 partitions. If used, zone 7 is no longer can be a combination of ADEMCO's 4204 Relay available as a protection zone.
  • Page 13 PSTN (Public Switched Telephone Network) descriptors are entered properly. Compatibility Improved Downloading Speed The initial release VISTA-120 is suitable for use in Uploads and downloads at 300 baud (predecessor many national telephone systems around the world, control rate is 75 baud), making upload/download...

  • Page 14: Planning A Partitioned System

    SECTION 2 Planning A Partitioned System This section provides the following information: • Theory of partitioning • Setting up a partitioned system • Common Area Logic • Master keypad setup and operation Theory of Partitioning This system provides the ability to arm and disarm up to 8 different areas, each as if it had its own control.

  • Page 15: Common Area Logic

    Common Area Logic When an installation consists of one or more partitions shared by users of other partitions in a building, those shared partitions may be assigned as the "common area" partitions for the system (programme fields 1*11, 1*14, 1*17). An example of this might be in a medical building where there are two doctor's offices and a common entrance area (see example that follows explanation).
  • Page 16 Example Here is an example of how the area would react in a typical setup. OFFICE #1 OFFICE #2 COMMON AREA MAIN ENTRANCE User #1 has access to Office #1 and the Common Area. User #2 has access to Office #2 and the Common Area. Office #1 is set up to affect the Common Area, but not arm it.
  • Page 17 How User Access Codes Affect the Common Area Codes with "Global" Arming If a code is given "global arming" when it is defined (see Section 24: SECURITY ACCESS CODES), the keypad will ask "Arm all?" or "Disarm all?" whenever the user tries to arm or disarm the partitions he has access to from a keypad.

  • Page 18: Master Keypad Setup And Operation

    Master Keypad Setup and Operation Although this system has eight actual partitions, it provides an extra partition strictly for the purpose of assigning keypads as "Master" keypads for the system. Any keypad assigned to Partition 9 in #93 Device Programming mode will become a "Master" keypad.

  • Page 19: False Alarm Reduction Features

    • Autobypass by User (not sent if using ADEMCO High Speed format • Autobypass by Zone (Sent as regular alarm if using ADEMCO High Speed format) • Bypass reports NOTE: If field *07 is enabled and field 1*20 is not enabled, then faults remaining in the exit route at the end of the exit delay will cause an immediate alarm.
  • Page 20 Cross-Zoning The Cross-Zoning feature is designed so that a combination of two zones must be faulted within a five minute period to cause an alarm on either zone. This prevents momentary faults from causing an alarm condition. You can select four pairs of cross zones, keeping in mind the following: •...

  • Page 21: Installing The Control

    CLIP 2. While holding the lock steady, insert UNLOCKED the retainer clip into the retainer slots. Use an Ademco No. N6277 Cam Lock CABINET DOOR BOTTOM and No. N6277-1 Push-On Retainer Clip Figure 1. Installing The Lock (supplied). Installing the Control's Circuit Board Refer to the Mounting the PC Board diagram.

  • Page 22: Standard Phone Line Connections

    Make certain that the mounting screws are tight. This insures that there is a good ground connection between the PC board and the cabinet. Also, dress field wiring away from the microprocessor (center) section of the PC board. Use the 2 loops on the left and right sidewalls of the cabinet for anchoring field wiring using tie wraps.

  • Page 23: Installing The Backup Battery

    24hr. source fuse inside the of AC mains transformer (non- replaceable). TRANSFORMER 16.5VAC, 40VA ADEMCO No.1361 NOTE: or 4300, XM10E, or WHEN POWERING UP XF10 if X-10 DEVICES THE PANEL, PLUG THE WILL BE USED. TRANSFORMER IN BEFORE CONNECTING THE BATTERY.

  • Page 24: Installing The Keypads

    SECTION 5 Installing the Keypads This section provides the following information: • A list of keypads that may be used • Instructions for wiring and mounting the wired keypads • Instructions for addressing the keypads • A preliminary check-out procedure to ensure that the keypads are functioning properly in the system Keypads That May Be Used •...

  • Page 25: Using A Supplementary Power Supply

    Using a Supplementary Power Supply to Power Additional Keypads The control provides 750mA of auxiliary standby power for powering keypads and other devices from the auxiliary power output. Aside from this, the control can support up to 32 peripheral devices (keypads, RF receivers, relay modules, etc.). The backup battery will supply power to these devices in the event that AC power is lost.
  • Page 26 3. Set each keypad to an individual address (00-30) according to the keypad's instructions. Set one alpha keypad for address "00" and other keypads for higher addresses (01, 02, and 03 are enabled in the system's default programme). Any keypads set for address 04 and above will appear blank until they are enabled in the system's programme.

  • Page 27: Basic Wired Zones 1-9

    SECTION 6 Basic Wired Zones 001-009 This section provides the following information • Common characteristics of wired zones • Wiring burglary and panic devices to zones 1-8 • Wiring 2-wire smoke detectors to zone 1 • Wiring 4-wire smoke detectors to zones 1-8 •...

  • Page 28: Wiring 2-Wire Smoke Detectors To Zone 1

    Photoelectric w/heat sensor, direct wire System Sensor 2100T † Photoelectric w/B110LP base System Sensor 2151 † NOTE: These smoke detectors are Listed for use with the VISTA-120 and are the only 2-wire smoke detectors that may be used in UL applications. –20–...

  • Page 29: Unsupervised Usage Of Zone 1

    Unsupervised Zone 1 can also be used for normally closed, unsupervised devices by doing the following: Usage of Zone 1 1. Cut the red jumper on the PC board located above Zone 1. 2. Connect closed circuit devices in series with terminals 10 and 11. When programmed for fire warning usage, all zones can monitor 4-wire smoke Wiring 4-Wire detectors or N.O.

  • Page 30: Compatible 4-Wire Smoke Detetors

    Compatible 4-Wire Use any 4-wire smoke detector which is rated for 10-14VDC operation and which has alarm reset time not exceeding 6 seconds. Some compatible 4-wire smoke Smoke Detectors detectors are listed below. Photoelectric, direct wire System Sensor 2412 Photoelectric w/heat sensor, direct wire System Sensor 2412TH Ionisation, direct wire System Sensor 1412...
  • Page 31 The alarm current provided by zone 8 will support only one Glass Break detector in the alarmed state. You can use detectors which exceed 1.1k ohms in alarm, provided they maintain a voltage drop in alarm of less than 3.8 volts. A.

  • Page 32: Polling Loop Zones 10-128

    SECTION 7 2-Wire Polling Loop Zones 010-128 This section provides the following information: • Polling loop overview • Common characteristics of polling loop zones • Wiring RPM devices to the polling loop • Addressing RPM devices • Polling loop limitations •...

  • Page 33: Polling Loop Limitations

    Refer to the 4297 Polling Loop Connection diagrams later in this section. DO NOT use the 4197 Polling Loop Extender Module with the VISTA-120. • Regardless of current drain, no more than 64 DIP switch devices or 119 serial number devices can be connected to the polling loop.

  • Page 34: Polling Loop Supervision

    (use the AUXILIARY CURRENT DRAIN WORKSHEET in the FINAL POWER UP PROCEDURE section. Notes: - Do not use the 4197 module with VISTA-120. - Refer to 4297 instructions for more detailed installation information.

  • Page 35: Maintenance Signal Support

    The control monitors maintenance signals from certain smoke detectors (4192CPM, Maintenance 4192SDM, 4192SDTM). Maintenance signals are triggered when a detector gets Signal Support dirty and indicate that the detector should be cleaned or replaced. If a detector maintains a high or low sensitivity condition for longer than 24 hours, the control sends a dialer report (trouble message for non-Contact ID reports;...

  • Page 36: Compatible Polling Loop Devices

    Compatible Polling Loop Devices 4208U 8-Zone Expander • Supports up to 8 zones via the polling loop. 4208UXM3 • Must use serial number enrollment mode. • The first two zones can be either normal or fast response (DIP switch selectable). •...
  • Page 37 Compatible Polling Loop Devices 998MX Dual PIR Dual element PIR eith built-in RPM (connects directly to the polling loop). • Must use serial number enrollment mode. • Tamper protected. • Anti-creep lookdown protection • Includes Fresnel lenses for wide angle and long range/curtain applications.

  • Page 38: Wireless (Rf) Zone Expansion

    Characteristics of • Individually assignable to one of 8 partitions Wireless Zones The VISTA-120 supports wireless zones which may be used exclusively or in Wireless Systems addition to basic wired and/or polling loop zones. The system supports either of Available...

  • Page 39: Wireless System Installation Advisories

    1. Place the receiver in a high, centrally located area for best reception. Do not Wireless System place receiver on or near metal objects. This will decrease the range and/or Installation block transmissions. Do not mount receivers or transmitters in an attic, Advisories where extreme temperatures could prevent proper operation.

  • Page 40: House Id Sniffer Mode

    POSITION POSITION 6: ON selects addressable mode for use with the 4140XMPT2 / VISTA-120, wherein positions 3-5 set the address. OFF selects non-addressable mode for use with the 4111XM / VISTA-25, where the settings of positions 3-5 must be OFF.

  • Page 41: 5700 Series Transmitter Setup

    make sure you do not choose a House ID that is in use in a nearby system. To enter this mode, proceed as follows: 1. Enter your "Installer Code" + # + 2 . 2. The receiver will now "sniff" out any House IDs in the area and display them. Keep the receiver in this mode for about 2 hours to give a good indication of the House IDs being used.

  • Page 42: Wireless Zone Assignments For 5700 Series Transmitters

    Each wireless zone can be assigned any zone response type, such as Entry/Exit, Wireless Zone Interior Follower, Perimeter, etc. (see the ZONE TYPES section for explanations Assignments for of each zone type). For 5700 series transmitters, each response type uses a 5700 Series certain range of zone numbers.

  • Page 43: Compatible 5700 Series Transmitters

    Compatible 5700 Series Transmitters Model Product Zone Num. Description 5701 Panic Transmitter 62 or 63 • Programmable for either silent or audible 24 hour alarm. 5706 Photoelectric Smoke 48-55 • One piece smoke detector with built Detector in transmitter. • Built-in 85 dB piezoelectric alarm sounder and audible low battery warning.

  • Page 44: 5800 Series Transmitter Setup

    5800/5800EU series transmitters have built-in serial numbers that must be 5800/5800EU "enrolled" by the system using the # 93 Menu mode programming, or input to the Series Transmitter control via the downloader 5800/5800EU series transmitters (except 5827 Setup described separately) do not have DIP switches Each transmitter's zone number is programmed into the system in # 93 mode.

  • Page 45: Compatible 5800 Series Transmitters

    Compatible 5800 Series Transmitters Model Product Enroll As Description Input Type 5801 Wireless Panic UR or RF • Has four pushbuttons, each with a Transmitter unique input (loop) code. • Programmable responses (e.g., Panic, Arm–Stay, Arm–Away, Disarm, etc. • For arming/disarming functions, button must be assigned to a user code when "adding a user."...
  • Page 46 • Has one unique input (loop) code. 5819 Shock Sensor Analyzer RF • Shock sensor analyzer for Ademco 5819S Transmitter Inertia Cross-Bar, Ultrak, Litton, Inertiaguard shock sensor. • Built-in reed magnetic contact.

  • Page 47: Checkout Procedure For Wireless Zones

    Go/No Go Test Mode Check-Out Before mounting transmitters permanently, conduct Go/No Go tests to verify Procedure for adequate signal strength and reorient or relocate transmitters if necessary. Wireless Zones During this mode, wireless receiver gain is reduced by 50%. Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for the installed system.

  • Page 48: Output Device Basics

    SECTION 9 Relay Outputs & Power Line Carrier (X-10) Devices This section provides the following information: • Output Device Basics • Wiring the 4204 relay module • Wiring the 4300 transformer Relays and Powerline Carrier devices (i.e., X-10 brand devices) are programmable Output Device switches that can be used to perform many different functions.

  • Page 49: Wiring The 4300 Transformer

    Wire Size Maximum SWITCH 4 2 0 4 A D D R E S S S E T T I N G S POSITION ("—" means "OFF") Length 0.64mm — — — — — — — — 0.81mm — — —...
  • Page 50 EARTH 16VAC IN GROUND J8 CONNECTOR TRANSFORMER YELLOW 220/230VAC BLACK 50HZ 4142TR CABLE RED / GREEN TRANSFORMER MODULAR CORD COLORS SYNC DATA COMMON Figure 16b. XF10 Transformer Connections J8 CONNECTOR AT CONTROL XM10E POWERLINE INTERFACE 4142TR CABLE 1 2 3 4 SYNC MODULAR PHONE CORD 1 - BLACK...

  • Page 51: 4285 Vista Interactive Phone (Vip) Module

    SECTION 10 4285 Vista Interactive Phone (VIP) Module This section provides the following information: • General information about the 4285 VIP module • Mounting and wiring the 4285 VIP module • Checkout procedure for the 4285 VIP module General The 4285 VIP Module is an add-on accessory that permits the user to access the security system and relays via a TouchTone (DTMF multifrequency) phone Information (either from the premises or by calling the premises from a remote location).

  • Page 52: Wiring The 4285 Vip Module

    2. When mounting the VIP Module outside the cabinet, use the screw holes at the rear to mount horizontally or vertically (double sided adhesive tape may be used, if preferred). You can bring wires out from the side or back (a round breakout is also available on the back).
  • Page 53 4285 WIRING NOTES: 1. If multifrequency (DTMF) tones are not present following phone access to the security system via an on-premises phone, try reversing the pair of wires connected to terminals 3 & 4 on the 4285, and the pair of wires connected to terminals 26 & 27 on the control. 2.

  • Page 54: Audio Alarm Verification (Aav) Unit

    SECTION 11 Audio Alarm Verification (AAV) This section provides the following information: • General information about the AAV option • AAV operation • Connecting an Eagle AAV Module General An Audio Alarm Verification (AAV) module (also known as two-way voice), such as the Eagle 1250, is an add-on accessory that permits voice dialogue between an Information operator at a central station and a person at the alarm installation, for the...

  • Page 55: Audio Alarm Verification Module Connections

    1. 685 Receiver software must be rev. 4.6 or higher. Earlier versions will not hold the phone line connection open. 2. Contact ID code for "listen-in to follow" is "606." Contact ID is the only reporting format that will send a "listen-in-to-follow." Connect the Audio Alarm Verification module's falling edge trigger input to J7 Audio Alarm connector trigger output, or to a 4204 relay module, as shown in the various AAV...

  • Page 56: Video Alarm Verification (Vav) Unit

    = 1 (alarm) start zone list = “n” (zone list** number containing camera zones for this relay) After all messages have been sent to the VISTA-120 Operation primary phone number during a reporting session, the control will Keypad...

  • Page 57: Voltage Triggers (Connector J7)

    SECTION 13 Voltage Triggers This section provides the following information: • General information about the voltage triggers • Ground Start trigger setup • Open/Close trigger setup • Keyswitch setup • Remote keypad sounder setup • Long Range Radio or other transmission media triggering Connector J7, located on the right hand side of the main PCB, provides 4 trigger General outputs.

  • Page 58: Ground Start Trigger Setup

    Output 1 may alternately be programmed for a remote keypad sounder. You may Remote Keypad use an Ademco PAL 328N piezoelectric sounder for installations where you want Sounder the sounds produced by the keypad's built-in piezo sounder to be duplicated in another location for one partition.

  • Page 59: Keyswitch Setup

    4142TR CABLE J7 CONNECTOR IF USED. 1. OUT 1 IS NO LONGER USABLE FOR OPEN/CLOSE OR GROUND START (SEE GRAY FIELD 1*46). 2. OUT 2, 3, 4 CAN STILL BE USED TO PROVIDE ALARM YELLOW BLACK STATUS INDICATIONS OR TO OPERATE A KEYSWITCH WHITE –...

  • Page 60: Keyswitch By Partition Configuration

    DPST or a DPDT keyswitch, Partition wherein the key is removable in two positions: AWAY and OFF (disarm). Ademco Configuration does not manufacture a packaged keyswitch with status LEDs (if status LEDs are desired, each must be driven by a programmed relay output).

  • Page 61: External Sounders

    Up to tems. 2k EOLR two 719 sirens can be used wired in • Wire the VISTA-120 door parallel. tamper switch in series with the AB12M tamper zone. Programming Option •...

  • Page 62: Event Log Options

    SECTION 15 Event Log Options This section provides the following information: • General information about the Event Log • Event Log printer connections • Displaying/Printing the Event Log General This system has the ability to record up to 224 events of various types in a history log (224 event capacity).

  • Page 63: Event Logging Procedures

    The 4100SM module package includes a 3m RS232 cable. You can use a longer cable or an extension cable if the Control and serial printer are separated by more than 3m. The total cable length should be less than 15m. 3.
  • Page 64 Use the [3] & [1] keys to scroll to the next and previous screens respectively: Displays time/date for zones that have either ALARM EVENT LOG caused an alarm or have been restored in selected TYPE CCC UUU partition. Displays time/date for zones that have caused a CHECK EVENT LOG trouble or supervisory condition in selected TYPE...

  • Page 65: Event Log Printer And Display Codes

    EVENT LOG PRINTER and DISPLAY CODES AC Power Fail..........AC LOSS Programme Mode Entered ......PROGRAM ENTRY AC Power Restore ........AC RESTORE Programmed Schedule was Changed..SCHEDULE CHANGE Auto Disarm..........DISARM-AUTO Real-Time Clock was Set......TIME SET Backup Battery Test Failed......BAT TST FAIL RF Expander Module Fail..

  • Page 66: Final Power-Up Procedure

    SECTION 16 Final Power-Up Procedure This section provides the following information: • Earth ground considerations • Connecting the AC transformer • Connecting the backup battery • Auxiliary and Polling Loop Current Drain Worksheets • You can power the control from a 1361 transformer, rated 16.5VAC, 40VA, General which plugs directly into a 24 hour, 120VAC, 60 Hz outlet.

  • Page 67: Connecting The Battery

    (time period varies depending on size of battery used) because the control Battery has a back-up, rechargeable gel type (sealed) lead acid battery. ADEMCO 467 (12V, 4AH) and ADEMCO 712BNP 12V, 7AH batteries are recommended. The standby battery is automatically tested every 4 minutes for 13 seconds (or every 50 seconds for 1.5 seconds, as a function of programme selection) and every...

  • Page 68: Polling Loop Current Drain Worksheet

    Use the following formula to determine the battery size needed: Calculating the Battery Size Needed [Total Current Drain (Amps)] X [Number of Hours Standby Needed] = [Battery Ampere Hours]. Example: If the total current drain is 550mA (.55 Amps), and 24 Hr. standby is needed: .55 X 24 = 13.2 Ampere/Hour battery.

  • Page 69: Access Control

    See the documentation included with the PassPoint ACS for details. The PassPoint ACS can dedicate some of its inputs for use as regular Vista-120 wired zones, (zone response type ACS). The PassPoint ACS can also utilise the Vista-120 dialler for reports to the central station.
  • Page 70 Programming the Wireless Keypad 1. Enter the partition to which the keypad is assigned in field 1*48. Using ACS Zone Inputs If the PassPoint ACS has uncommitted zones, these may be used by the Vista-120 as wired zones. Programming the ACS Zone Inputs 1.

  • Page 71: Wiring The Vista Gateway Module

    The Vista-120 relays or the ACS relays or triggers would be used with keypads and/or RF transmitters whose response type is Access Point (27) to control these devices.

  • Page 72: Programming The System

    PART 2 PROGRAMMING THE SYSTEM –64–...

  • Page 73: The Mechanics Of Programming

    Defaults • There are four sets of pre-programmed communication defaults available, including Low Speed, 4+2 Express, Ademco High Speed, and Ademco Contact ID. Loading one of these defaults automatically programs industry standard codes that will suit most of your needs.

  • Page 74: Moving From One Page Of Programming To Another

    Enter the first field number to be programmed (ex. *00, installer's code) and make the desired entry. When the field is complete, the keypad will normally "beep" three times and will advance to the next field. If you do not desire to change the next field, press [ ]and the next field number to be programmed.

  • Page 75: Programming Partition Specific Data Fields

    To proceed, enter + the next data field you wish to programme (ex. press *05). Partition-Specific programming fields are skipped. 4. To change to the next page of fields, press *94. To return to the previous page of fields, press *99. To program partition-specific data fields once in programme mode, do the Programming following:...

  • Page 76: Zone Index & Zone Type Definitions

    This section provides the following information: • Zone number designations • Zone Type Definitions The VISTA-120 has 128 physical zones, as well as supervisory zones for relays, Zone Index ECP devices (devices which communicate through the keypad terminals), and system troubles. These zones are designated as follows: ZONE No.

  • Page 77: Zone Response Type Definitions

    ZONE RESPONSE TYPE DEFINITIONS Type 00: Zone Not Used Type 05: Trouble by Day/Alarm by Night Programme a zone with this zone type if the zone is This zone type will give an instant alarm if faulted not used. when armed in the Away, Stay, Instant or Maximum (night) modes.
  • Page 78 Type 27: Access Point This zone type can be used on zones that are to signal to the Ademco Passpoint ACS to request unlatching of a door lock linked to this zone. – 70 –...

  • Page 79: Data Field Descriptions

    SECTION 20 Data Field Descriptions The following is a description of all data fields provided by this control. Make entries as described for each field. INSTALLER CODE | | | 0001-9999 = 4-digit installer's code The Installer's Code is reserved for installation company use, and is the only code that can be used to enter Programme mode from the keypad.

  • Page 80: Zone 9 Response Time

    ENTRY DELAY #1 (partition-specific) [02] 01-15 times 15 seconds 00 = no delay Entry delay defines the delay time which allows users to reenter the premises through a door that has been programmed as an entry delay door (zone type 01)and disarm the system without sounding an alarm. The system must be disarmed within this period or an alarm will occur.

  • Page 81: Randomise Ac Mains Loss Report

    RANDOMISE AC MAINS LOSS REPORT 1 = randomise AC loss reporting between 30-60 minutes after an actual AC loss 0 = normal AC loss reporting (about 2 minutes after actual AC loss) Selecting this option helps prevent an overload of AC loss messages at the central station during a community blackout.

  • Page 82: Power Up In Previous State

    Note that whether or not multifrequency dialing for call placement is permitted, communication by the use of DTMF signaling (Ademco Expanded High Speed, Ademco 4+2 Express, Ademco Contact ID) will still take place. See field 1*33 for multifrequency w/pulse dial backup.

  • Page 83: Secondary Phone Number

    SECONDARY PHONE NUMBER | | | | | | | | | | | | | | | | | Enter the secondary phone number, up to 17 digits, 0-9; enter #11 for *, #12 for #, and #13 for a 2 sec. pause. It is used if communication on the primary number is unsuccessful, or if split/dual reporting is desired.
  • Page 84 Only applicable if using a 4285 telephone module and/or if remote initiated downloading will be used. PRIMARY FORMAT 0 = Low Speed 2 = Ademco Expanded High Speed 1 = Contact ID 3 = Ademco Express Selects the reporting format for use on the primary telephone number.

  • Page 85: Telephone System Selection

    MAXIMUM No. OF DIALLER ATTEMPTS 1-8 = number of dialler attempts TELEPHONE SYSTEM SELECTION [00] 00=Latin America, Spain, Italy, Eastern Europe, China † 01= Australia † 02= Belgium † 03= Denmark † 04= Finland † 05= France † 06= Netherlands †...

  • Page 86: First Test Report Time

    FIRST TEST REPORT TIME 00-07 = day that the first test report shall be transmitted 00-23 hours/00-59 min. = time that the first test report shall be transmitted 00 = immediately upon exiting programme mode 00 entry in the day location will cause the report to be sent at the next occurrence of the time that is set.

  • Page 87: Bypass Enable For Fire Zones

    BYPASS ENABLE FOR FIRE ZONES 1*05 Yes, allow bypass of fire zones 2= No, fire zones cannot be bypassed SUPPRESS ALL KEYPAD DISPLAYS 1*06 WHEN SYSTEM IS ARMED 1= Yes 0= No DISPLAY TRBL INSTEAD OF CHECK 1*07 1 = display the letters TRBL instead of CHECK when a zone or system trouble occurs.

  • Page 88: Cross Zoning

    COMMON AREA 3 PARTITION 1*17 1-8 = common area 3 partition = none AFFECTS COMMON AREA 3 1*18 (partition-specific) 1 = this partition affects common area 3. This partition will cause common area 3 to disarm when this partition disarms. 0 = this partition does not affect common area 3 ARMS COMMON AREA 3 1*19...

  • Page 89: Rf Tx Low Battery Report Enable

    RF TX LOW BATTERY REPORT ENABLE 1*29 1 = a trouble message for RF transmitter low battery conditions sent to the central station. 0 = no report for transmitter low battery is desired. Note that a trouble message will be sent for a transmitter supervision failure independent of this selection.

  • Page 90: Call Waiting Defeat

    USER BYPASS OF TAMPER FAULTS INSTEAD OF 1*39 INSTALLER ONLY BYPASS 1 = yes 0 = no (ANPI requirement) MAX. NUMBER OF ZONES THAT CAN BYPASSED PER 1*40 [00] PARTITION (partition-specific) 01-15, 00 = no restriction (must not be 00 for ANPI compliance) BYPASS/UNBYPASS ZONES WHEN ARMED 1*41 1 = able to bypass and unbypass non-fire zones while the system is...

  • Page 91: Disable Download Callback

    No. of SECONDS ADDED PER DAY 1*50 00-30 = the number of added seconds per day to correct the real-time clock No. OF SECONDS REMOVED PER DAY 1*51 00-30 = the number of subtracted seconds per day to correct the real-time clock SEND CANCEL IF ALARM + OFF 1*52 (partition-specific)

  • Page 92: Video Alarm Verification

    VIDEO ALARM VERIFICATION 1*67 1 = Video Alarm Verification (VAV) is being used. This selection enables transmission of Contact ID Event Code 609 to signal the central station equipment to ready itself for video image reception and processing. 0 = otherwise EVENT LOG TYPES 1*70 Alm Chck Byps O/C Systm...

  • Page 93: Allow Disarm Outside Window If Alarm Occurs

    AUTO-ARM DELAY 2*05 (partition-specific) [15] 01-14 = (times 4 minutes) the time between the end of the arming window and the start of auto arm warning time = no delay is desired. = auto arming is not desired. AUTO-ARM WARNING PERIOD 2*06 (partition-specific) [15]...

  • Page 94: Use Partition Descriptors

    USE PARTITION DESCRIPTORS 2*19 1 = partition descriptors will be programmed. If enabled, the normal keypad display will include a partition number and four-character descriptor). 0 = cause the keypads to display a non-partitioned system type of display (no partition number will appear). ENABLE J7 TRIGGERS BY PARTITION 2*20 (partition-specific)

  • Page 95: #93 Menu Mode Programming

    SECTION 21 #93 Menu Mode Programming This section provides the following information: • #93 Menu Mode main menu options • Zone Programming • Serial Number Programming • Report Code Programming • Alpha Programming • Device Programming • Relay Programming • Relay Voice Descriptors •...
  • Page 96 DEVICE PROG? defining following device characteristics 0=no 1=yes addressable devices, including keypads, receivers (4281/5881/5882EU), 4204 output relay modules, and 4285 VIP Module and VGM • Device Address • Device Type • Keypad Options (incl. partition assignment) • RF House ID RELAY PROG? For defining output relay functions.

  • Page 97: Zone Programming

    Zone Programming (this section has been revised from previous manuals) Enter Programming mode [Installer Code] + 8 0 0 0. The following fields should be programmed before beginning: 2*00: Number of Partitions; 1*32: RF Receiver Type. Also, before programming wireless zones, the RF receiver must be enabled in Device Programming Mode (procedure described later in Device Programming section).
  • Page 98 020 Zone Response Each zone in a system must be assigned a zone type, which defines Zone Disabled 00 the way in which the system responds to faults in that zone. Refer to ZONE TYPE DEFINITIONS section for detailed definitions of each zone type.
  • Page 99 If input type 6 was selected, this prompt will be displayed. Enter 1 010 SMART CONTACT for devices that monitor maintenance signals (ex. 5192SD, 1 = YES 0 = NO 5192SDT, 5808). Otherwise, enter 0. V-PLEX RELAY? If input type 6 was selected, this prompt will be displayed. Enter 1 1 = YES 0 = NO if using 4208UXM or 4101SN relay module for this zone.
  • Page 100 The system will then enter an optional confirmation mode so that the operation of the actual programmed input can be confirmed. Activate the loop input or button that corresponds to recommend that confirm this zone. programming of every device before proceeding to the next zone.

  • Page 101: Sequential Mode Programming

    Sequential Mode Programming (this section has been revised from previous manuals) Usually, serial numbers are enrolled during zone programming. If not, use #93 menu mode to enroll serial numbers (for example, if all other programming was done via downloading). Use this mode only after all other zone information has been programmed, including transmitter loop numbers.
  • Page 102 If the first zone number entered does not have one or more of the above attributes, the system will search its database for the first zone that does and will display it on the next screen. This prompt is displayed when the system has found the next 010 INPUT S/N zone which needs to be enrolled.

  • Page 103: Report Code Programming

    All report codes are entered using #93 menu mode programming, either through Report Code Programming, or through the Zone Programming mode while entering other zone information. In the Vista-120, reports are divided into six categories. These categories represent the main menu options found in the Report Code Programming mode. Reports and...
  • Page 104 Zone Alarm Reports Press 1 (Y) to enter alarm report codes for zones. ALARM, ID DIGIT? 1 = YES 0 = NO Press 0 (N) to skip to the next main menu option. ENTER ZONE NO. Enter the zone number for which you are entering 000 = QUIT the report code.
  • Page 105 System Group 1 Codes To enter System Group #1 codes, press 1 (Y). SYSTEM GROUP #1? 1 = YES 0 = NO CLOSE Enter the first digit of the Closing (Arm-Away) report. Press 1st 00 2nd 00 . Enter the second digit of the report. If the user number is desired as the second digit, enter 01 (not necessary for Contact ID or High Speed formats).

  • Page 106: Programming Alpha Descriptors

    Programming Alpha Descriptors General Information • You can programme a user friendly English language description/location keypad display for all protection zones, relays, keypad panics, polling loop short, and RF receiver supervision troubles. • Each description can be composed of a combination of words (up to a maximum of 3) that are selected from a vocabulary of 244 words stored in memory, and any word can have an "s"...
  • Page 107 b) Select the first letter of the desired description (note that "A" is already displayed). Use the [3] key to advance through the alphabet and the [1] key to go backward. Press the [3] key repeatedly until "B" appears (press [1] to go backwards if you happen to pass it), then press key [6] to display the first available word beginning with B.
  • Page 108 6. Save the word by pressing the [8] key. This will return you to the CUSTOM WORD? display. The custom word (or string of words) will be automatically added to the built-in vocabulary at the end of the group of words beginning with the same letter.

  • Page 109: Alpha Descriptor Vocabulary

    ALPHA DESCRIPTOR VOCABULARY (For Entering Alpha Descriptors. To select a word, press [#] followed by the word's 3-digit number.) NOTE: This vocabulary is not to be used for relay voice descriptors. See the RELAY VOICE DESCRIPTORS section when programming relay voice descriptors. 000 (Word Space) 102 INTERIOR 151 POLICE...

  • Page 110: Device Programming

    Device Programming This menu is used to programme keypads, receivers and relay modules. From Data Field Programming mode, press #93 to display "ZONE PROG?". Press 0 repeatedly to display "DEVICE PROG?". DEVICE PROG? Press 1 to enter DEVICE PROGRAMMING mode. 1=YES 0=NO The device address identifies the device to the control.

  • Page 111: Relay Programming

    Relay Programming The system supports up to 32 X-10 and/or relay outputs, plus up to 64 polling loop trigger/relay outputs. Once a device is programmed, there is no distinction between an X-10, triggers, or relay output device. Relays can be used to perform different functions and actions. Each relay must be programmed to begin one of four types of ACTIONS at a designated START event, and end that ACTION at a designated STOP event.

  • Page 112: Programming Output Devices

    The “ZONE TYPE” option functions independently of the “EVENT/ZONE LIST” combination. b.PARTITION No. (P). The device's "Start" ZONE TYPE/SYSTEM OPERATION may be limited to an occurrence on either one partition (1-8) or any partition (0). The "STOP" programming determines when and under what conditions the STOP (STP): device will be de-activated.
  • Page 113 01 Start: Zn LIST A Zone List is a set of zones that can be used to initiate the start or No list stop relay action. If a zone list is being used to start this relay action, enter the Zone List number 01-15. If a zone list is not being used, enter 00.

  • Page 114: Zone List Programming

    Enter 0 for polling loop trigger or relay. Enter 1 for 4204 relay Relay Type outputs. Enter 2 for Powerline Carrier devices. Press continue. For polling loop trigger outputs (4208UXM)/4101SN), enter the V-PLEX ZONE # protection zone number (010-128) linked to each output, if used. If not using a protection zone on these modules, enter the relay zone number (601-696).

  • Page 115: Relay Voice Descriptors

    View Zn LIST This will appear if 00 is pressed at the ENTER ZONE LIST prompt. 00=QUIT 00 Enter the zone list number that you wish to view. Press continue. XX ASSIGNED ZONE Press to scroll through all zones in that list. Enter 00 + 000=QUIT 000 quit.

  • Page 116: Module

    Relay Voice Descriptors and Custom Word Substitutes Vocabulary Word Index Word Index Word Index Word Index Word Index Air......116 Daughter's ... 208 Garage ....023 Off......011 South....155 Alarm ....255 Den ...... 052 Gas.......138 Office ....147 Stairs....006 And.......067 Detector ....128 Glass ....139 On......

  • Page 117: Rf Serial Number Clear Mode

    RF Serial Number Clear Mode This mode may be used in the event that an undesired transmitter has been enrolled during sequential enrolling, causing each subsequent serial number to be assigned to an incorrect zone. Performing this operation will delete all RF serial numbers, leaving all other zone information intact.

  • Page 118: Scheduling Options

    SECTION 22 Scheduling Options This section provides the following information: • Main features of scheduling • Time Window Definitions • Open/Close Schedule Definitions • Programming in the #80 Scheduling menu mode • Programming: Time Windows Open/Close Schedules Holiday Schedules Time Driven Events Access Schedules Introduction To Scheduling This section describes the scheduling features provided with this control panel.
  • Page 119 Extend Closing • A user can manually extend the arm (closing) time window Window by 1 or 2 hours. This is done by entering a keypad command (security code + #82), which then prompts the user to enter the desired extension time of 1 or 2 hours (refer to the SYSTEM OPERATION section...

  • Page 120: Time Windows Definitions

    Time Windows Definitions Time Windows • Scheduled events are based on time windows, which are simply periods of time during which an event may take place. Time windows are defined by a start time and stop time. The system supports up to 20 Time Windows. The windows are shared by the 8 partitions, and the windows are used for open/close schedules as well as for time driven event control.

  • Page 121: Open/Close Schedule Definitions

    Open/Close Schedule Definitions General • The Open/Close scheduling is controlled by one of three individual schedules. Each schedule consists of one time window for openings and one time window for closings. There are three types of schedules available: Daily, Holiday, and Temporary. Daily Schedule •...

  • Page 122: Programming With #80 Scheduling Menu Mode

    Example of Open/Close Exception Reporting & Scheduling 6:01PM 5:59AM 9:01AM 3:59PM 6:01PM 5:59AM "Early opening" reports Opening Window Auto-disarm delay begins . Closing Window Auto-arm delay begins will be sent if system No reports sent Auto-disarm occurs after delay. No reports sent Auto-arm warning begins.

  • Page 123: Basic Scheduling Menu Structure

    Steps To Programming Scheduling Options To use #80 Scheduling Menu Mode, do the following: Using the worksheets: Define time windows (up to 20) Define the daily open/close schedules (one schedule per day, per partition) Define the holidays to be used by the system (up to 16) Define the holiday schedules (up to 8, one per partition) Define temporary schedules Define limitation of access times (up to 8 schedules)

  • Page 124: Time Window Definitions Worksheet

    The system provides 20 time windows that are defined with start and stop times. Time Windows These windows are used for various open/close and access schedules, as well as for Definitions output controls and are the basis of the scheduling system. These windows are shared Worksheet among all 8 partitions.

  • Page 125: Programming Time Windows

    Programming Time Windows Enter Scheduling Mode by entering the installer code + # + 80. The keypad will display the Time Window programming prompt. Time Window ? Enter 1 at this main menu prompt to programme time 1 Yes 0 = No windows.

  • Page 126: Programming Open/Close Schedules

    Programming Open/Close Schedules Each partition can be assigned one daily open/close schedule, plus a holiday open/close schedule. Temporary schedules are programmed separately, using the #81 Temporary Schedule Menu Mode. To programme additional open/close schedules, see the Time Driven Events section. After entering Scheduling Menu Mode, press 0 until the O/C Schedules prompt appears.

  • Page 127: Holiday Definitions & Schedule Worksheet

    Holiday Definitions & Schedule Worksheet Hol. Partition Month/Day Programming Holiday Schedules Up to 16 holidays can be defined for the system. After entering Scheduling Menu Mode, press 0 until the Holidays ? prompt appears. Holidays ? Enter 1 to programme holiday schedules. 1 Yes 0 = No HOLIDAY NUMBER ?

  • Page 128: Time-Driven Events

    Time-Driven Events These are the schedules used to activate outputs, bypass zones, etc. based on a time schedule. There are 20 of these events that may be programmed for the system, with each event governed by the previously defined time windows. The actions that can be programmed to automatically activate at set times are relay commands, arm/disarm and zone bypassing commands, and open/close access conditions.

  • Page 129: Time Driven Event Worksheet

    Action Code Action Specifier Auto bypass - Zone list Zone list # Auto unbypass - Zone list Zone list # Open/Close Windows Activation time 3 (During) is the only valid choice for these commands. Action Code Action Specifier Enable Opening Window by partition Partition(s) Enable Closing Window by partition Partition(s)

  • Page 130: Time-Driven Event Programming

    Time-Driven Event Programming The following schedules can be used to activate outputs, bypass zones, arm/disarm the system, etc. based on a time schedule. Up to 20 events can be programmed for the system. Time windows must first be defined in order to be used to trigger events.
  • Page 131 30=Auto bypass - Zone list Actions 30-31 01 ZONE LIST ? 31=Auto unbypass - Zone list ENTER 1-8 Enter the zone list number which contains the zones to be bypassed or unbypassed. Press to accept entry. The Time Window ? prompt appears.

  • Page 132: Limitation Of Access By Time Worksheet

    Limitation of Access by Time Worksheet Limitation of Access is a means by which a user's access code is limited to working during a certain period of time.. The system provides 8 Access Schedules, each of which consists of two time windows for each day of the week and two time windows for holidays (typically one for an opening time window and the second for a closing time window).

  • Page 133: #81 Temporary Schedule Menu Mode

    #81 Temporary Schedule Menu Mode Each partition can be assigned a Temporary Schedule which will override the regular open/close schedule (and the holiday schedule). This schedule takes effect as soon as it is programmed and remains active for up to one week. Partition/Windows Disarm Window Start Time HH:MM...

  • Page 134: Programming Temporary Schedules

    Programming Temporary Schedules Enter [Security Code] + # + 81 to enter this mode. Note that only users with authority level of manager or higher can programme temporary schedules. Temporary schedules only affect the partition from which it is entered. Temporary schedules can also be reused at later dates simply by scrolling (by pressing #) to the DAYS? prompt (described below) and activating the appropriate days.

  • Page 135: #83 User Scheduling Menu Mode

    #83 User Scheduling Menu Mode The system provides up to 20 "timers" which will be available to the end user for the purpose of controlling output devices (4204 relays or Powerline Carrier devices (e.g., X-10). These timers are analogous to the individual appliance timers that might be purchased at an electrical appliance store.

  • Page 136: System Communication

    Ademco 685 receiver using software level 4.4 or higher. Must be level 4.7 or higher to fully support all new VISTA-120 report codes. 685 software levels below 4.4 cannot support Contact ID reporting. For information regarding updating the 685 receiver, contact your nearest Ademco Support location.
  • Page 137 ("new" or "restore"), 3-digit event code, 2-digit Partition No., and 3-digit zone number, user number, or system status number. Ademco Expanded High Speed Comprised of 13 digits as follows: A 4-digit account number + eight channels of zone information (1-8 or duress plus 9-15) + one status channel, which identifies the type of events being reported in the eight zone locations.
  • Page 138 1234 5115 5555 7 (Acct #1234 with alarms on channels 2 and 3) LIMITATIONS 1. When using Ademco Expanded High Speed, remember there are only 15 channels available, plus a duress channel. If more than 15 zones are being used, they will have to share channels.

  • Page 139: Loading Communication Defaults

    Loading Communication Defaults To help expedite the installation, the system provides 4 different communication defaults (Low Speed, Ademco Express, Ademco High Speed & Ademco's Contact ID). These defaults automatically programme industry- standard code assignments for zones, keypad panics, non-alarm and supervisory conditions, and can be loaded at any time without affecting non- communication programme fields.
  • Page 140 TABLE OF CONTACT ID EVENT CODES Code Definition Code Definition Fire Alarm Cancel by User Smoke Alarm (Fire w/Verification) Remote Arm/Disarm (Download) Water Flow Alarm Quick Arm Duress Keyswitch O/C Silent Panic Call back Requested Audible Panic Access Denied Duress Access Grant Access Granted Duress Egress Grant Door Force Open...

  • Page 141: Communication Programming Guide

    Alarm restore is "E" + 2nd digit. • Enables all zone type restores. ADEMCO High Speed • Selects Ademco High Speed format, with no checksum, for both phone (*94*82) numbers. • Zone reporting is assigned to channels as described later in this section.
  • Page 142 Bypass Trbl Opn/Cls Low Bat No checksum Primary Secondary SESCOA/RADIONICS SELECT Radionics COMMUNICATION DEFAULTS for ADEMCO EXPANDED HIGH SPEED FORMAT (*94*82) PRIMARY FORMAT Ademco Exp. High Spd DUAL REPORTING STANDARD/EXPANDED REPORT FOR PRIMARY LOW SPEED FORMAT (Primary) standard SECONDARY FORMAT Ademco Exp.

  • Page 143: Communication Defaults For Zones

    Communication Defaults For Zones To programme report codes, see Report Code Programming in the #93 MENU MODE PROGRAMMING section. ZONE # LOW SPEED EXPRESS HIGH SPEED CONTACT ID - 135 -...
  • Page 144 COMMUNICATION DEFAULTS FOR ZONES (cont'd) ZONE # LOW SPEED EXPRESS HIGH SPEED CONTACT ID – 136 –...
  • Page 145 COMMUNICATION DEFAULTS FOR ZONES (cont'd) ZONE # LOW SPEED EXPRESS HIGH SPEED CONTACT ID - 137 -...
  • Page 146 COMMUNICATION DEFAULTS FOR ZONES (cont'd) ZONE # LOW SPEED EXPRESS HIGH SPEED CONTACT ID ALARM RST. TROUBLE TRBLE. RST BYPASS BYPASS RST. DURESS (992) – 138 –...

  • Page 147: Downloading

    Anything that can be done directly Information from the keypad can be done remotely, using ADEMCO's VLINK ® downloading software. To communicate with the control panel, the following is required: 1. An IBM PC compatible 286, 386, 486 or Pentium computer with at least 1MB RAM, a hard disk with 12MB available disk space, running MS DOS 3.1 or...

  • Page 148: On-Line Control Functions

    1. Alarm and trouble responses and reports are only disabled during EEROM update during on-line time. Should an event occur during this time, the response will take place and the report will go through as soon as the remote access sequence is completed. Alarm and trouble conditions are not ignored, they are simply delayed.

  • Page 149: Connecting A 4100Sm Module For Direct Wire Downloading

    CONTROL/COMM ACCESS: Read Only: able only to Upload and arm the system. Not able to DISARM, BYPASS, or change any information. Part Read/Write: able to ARM, BYPASS, UPLOAD, DOWNLOAD but cannot shutdown the system. Full Read/Write: able to perform all control and status commands, as well as shutdown all or part of the system.

  • Page 150: Setting The Real-Time Clock

    SECTION 25 Setting The Real - Time Clock This section provides the following information: • General information about the real-time clock • Setting the time and date General Information This system provides a real-time clock, which must be set in order for the system's event log to keep track of events by time and date.

  • Page 151: Part 3 System Operation And Testing

    PART 3 SYSTEM OPERATION AND TESTING - 143 -...

  • Page 152: Security Access Codes

    SECTION 26 Security Access Codes This section provides the following information: • General information about security access codes • Definition of user authority levels • How to add a user access code • How to change a user access code •...

  • Page 153: Open/Close Reporting

    Level 0: Installer (User 1) • Programmed in field *00 (default=4-1-4-0). Installer open/close reporting is selected in field *39. • Can perform all system functions (arm, disarm, bypass, etc.), but cannot disarm if armed by another code (or by Quick Arm). •...
  • Page 154 Levels 3-5: Operator Codes • Can arm and disarm the system to the authority assigned, but cannot add or modify any user code. • May operate a partition with one of the three OPERATOR authority levels A through C listed below. Level Title Functions Permitted...

  • Page 155: To Add A Master, Manager Or Operator Code

    Ademco Contact ID format is capable of reporting Users 001-150 uniquely. If any other report format is used, only user numbers #1 - #15 can uniquely report to the central station. Users #16 - #150 will report as User #15.
  • Page 156 for this user. Open/Close Rep.? Press 0 (NO) or 1 (YES), depending on whether or not 0 = NO , 1 = YES arming/disarming by this user will trigger opening & closing reports. This prompt appears only if the installer code is used to add a user.

  • Page 157: To Change A Master, Manager Or Operator Code

    Enter Installer code* + [8] + User number (002-150) + new user's code. To CHANGE a * Or Master or Manager code, but must be code with higher level of authority than Master, Manager the code being changed. (i.e. Master code can change a Manager or Operator level or Operator Code code, but cannot change another Master code;...

  • Page 158: Keypad Functions

    SECTION 27 Keypad Functions This section provides the following information: • General information about keypad usage • Basic keypad functions • Global arming • Access control • Delaying closing time • Executing the "Go To" command • Viewing: Built-in user's guide A user's capabilities Zone descriptors Downloaded messages...

  • Page 159: Global Arming

    Bypassing Zones Enter code + 6 (BYPASS) + zone number. To automatically bypass all faulted zones, use "Quick Bypass" method: Enter code + BYPASS + # . Chime Mode Enter code + 9 (CHIME) . To turn chime mode off, enter code + CHIME again.

  • Page 160: Partition "Go To" Command

    If Open/Close schedules are used, end users can manually delay closing time by Delaying Closing extending the closing window by 1 or 2 hours. This is useful if a user must stay on the Time premises later than usual. The user must have authority level of manager or higher. To extend the closing window, enter user code + # +82.

  • Page 161: Panic Keys

    Panic Keys There are three panic key pairs (shown below) or three lettered keys (A, B, or C) that, if programmed, can be used to manually initiate alarms and send a report to the central station. Each key pair can be individually programmed for 24 Hour Silent, Audible or Auxiliary (Emergency) responses, as well as Fire.

  • Page 162: Manual Relay Activation Mode (#70)

    The system allows users to manually activate relays/X-10 modules by keypad command Manual Relay using either the keypad or a telephone keypad (if VIP module is used). The user will be Activation Mode prompted (by keypad alpha display or telephone voice module). (#70 Mode) To activate relays from a keypad, enter 4-digit security code + [#] +70.

  • Page 163: Testing The System

    --Armed Burglary System test • Turning the system over to the user When AC power is present, the VISTA-120 will run a brief (13 seconds) battery Battery Test test every 4 minutes (alternatively, the test can be for 1.5 seconds every 50 seconds) to determine if there is a battery connected, and will run an extended battery test every 24 hours to check on the battery's condition.

  • Page 164: Armed Burglary System Test

    1. Alarm messages will be sent to the central station during the following tests. Armed Notify the central station that a test will be in progress. Burglary 2. A display of "COMM. FAILURE" indicates a failure to communicate (no Kissoff System Test by the receiver at the central station after the maximum number of transmission attempts is tried).

  • Page 165: Turning The System Over To The User

    Other System Messages • "COMM. FAILURE" at the keypad Indicates that a failure occurred in the telephone communication portion of your system. • "LO BAT" and a zone descriptor, accompanied by a once per minute beep at the Keypad Indicates that a low battery condition exists in the wireless transmitter displayed.

  • Page 166: Regulatory Agency Statements

    REGULATORY AGENCY STATEMENTS IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS In the event of telephone operational problems, disconnect the control panel by removing the plug from the RJ31X wall jack. We recommend that you demonstrate disconnecting the phones on installation of the system.

  • Page 167: Dip Switch Tables

    DIP SWITCH TABLES FOR ADDRESSABLE POLLING LOOP DEVICES 4190WH ZONE EXPANDER APPLIES TO TABLE A & B SHOWN SET FOR ID 10 (A) 1 2 3 4 5 6 7 8 SIDE VIEW (DN) WITH TABLE: POS.1 MUST BE: THIS TABLE FOR DIPS WITH THIS TABLE FOR DIPS WITH THIS TABLE FOR DIPS WITH THIS TABLE FOR DIPS WITH...

  • Page 168: Surface Mount

    DIP SWITCH TABLES FOR POLLING LOOP DEVICES 4278EX PIR 4194 REED CONTACT 4275EX PIR (SURFACE MOUNT) MIRROR MIRROR SHOWN SET FOR SHOWN SET FOR SIDE VIEW SHOWN SET FOR ID 10 ID 10 ID 10 (DN) SIDE VIEW SIDE VIEW 1 2 3 4 5 6 (DN) 1 2 3 4 5 6 7 8...

  • Page 169: Dip Switch Tables For 5700 Rf System Wireless Devices

    DIP SWITCH TABLES FOR 5700 RF SYSTEM WIRELESS DEVICES 5775 PIR HOUSE ID 5701 PANIC TRANSMITTER 5706/5707 SMOKE DETECTOR/TRANSMITTER SWITCH SETTING FOR ALL DETECTORTRANSMITTER DEVICES EXCEPT 5716 MIRROR HOUSE ID (1 SHOWN) DIP SWITCH POSITION DEVICE SIDE 1 2 3 4 5 6 VIEW (UP) —...

  • Page 170: Specifications

    318mm Wide X 368mm High X 76mm Deep Electrical: VOLTAGE INPUT: In 110 volt AC mains systems, from Ademco No. 1361 Plug-In Transformer (use 1361CN in Canada) or 4300 transformer (for X- 10 installations) rated 16.5VAC, 40 VA or XF10 transformer (for 220VAC, 50Hz X-10 installations) ALARM SOUNDER OUTPUT: 10VDC-13.8VDC (10.7VAC-14.5VAC for Vista-120FR), 2.8 amps...
  • Page 171 Adding An RF Key To An Existing User, 149 Daily Open/Close Worksheet, 117 addressable devices, 3, 16, 88 Data Field programme mode, 65 Ademco Expanded High Speed Reporting, 130 Delaying Closing Time, 152 Ademco Express, 5, 76, 131, 134 Delete a Master, Manager or Operator Code, 149...
  • Page 172 EVENT LOG PRINTER ON-LINE, 84 Operator level B, 144 EVENT LOG TYPES, 84 Operator level C, 144 exception reporting, 113 output devices, 4, 40, 107, 111, 127 EXIT DELAY #1, 72 PABX, 12, 14, 74 EXIT DELAY #2, 72 PAL 328N, 50 EXIT DELAY RESET, 80 PANIC BUTTON OR SPEED KEY, 80 EXIT DELAY SOUNDING, 82...
  • Page 173 SESCOA/RADIONICS SELECT, 76 Setting the Time and Date, 142 SILENCE SOUNDER DURING AAV, 83 Silent Panic/Duress trigger, 52 SOUNDER TIMEOUT, 72 Speed Keys, 153 STANDARD/EXPANDED REPORT, 76 SUMMER TIME, 84 Supervised Fire, 69 SUPPRESS ALL KEYPAD DISPLAYS, 79 SUPPRESS FIRE ALARM RELAY, 75 SUPPRESS KEYPAD ARMING STATUS INDICATIONS, 79 SUPPRESS TX SUPERVISION SOUND, 82 SUPPRESS USE OF "ARMED"...
  • Page 174 WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced wireless security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a vari- ety of reasons.
  • Page 175 WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. NOTES: 1. Zone 1 may be selected for EOLR supervised Zone 7 may be used for remote keyswitch J7 Header J8 Header MAKE CONNECTIONS USING or normally closed (no EOLR) operation via arming/disarming.
  • Page 176 24 months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply.

Table of Contents