How To Define A Mac-Port-Ip Address Binding Rule; How To Define A Mac-Port-Protocol Binding Rule - Alcatel OmniSwitch 6624 Network Configuration Manual
Hide thumbs
Also See for OmniSwitch 6624:
- Troubleshooting manual (614 pages) ,
- Management manual (264 pages) ,
- Network configuration manual (654 pages)
Table of Contents
Advertisement
Defining VLAN Rules
How to Define a MAC-Port-IP Address Binding Rule
To define a MAC-port-IP address binding rule, enter vlan followed by an existing VLAN ID then
binding mac-ip-port followed by a valid MAC address, IP address, and a slot/port designation. For
example, the following command defines a MAC-port-IP binding rule for VLAN 255:
-> vlan 255 binding mac-ip-port 00:00:da:59:0c:12 21.0.0.10 2/3
In this example, frames received on mobile port 2/3 must contain a source MAC address of
00:00:da:59:0c:12 and a source IP address of 21.0.0.10 to qualify for dynamic assignment to VLAN 255.
Use the no form of the
that it is only necessary to enter the rule's MAC address parameter value to identify which rule to remove.
-> vlan 255 no binding mac-ip-port 00:00:da:59:0c:12
Note that this binding rule type is also supported on AVLANs. See
cated VLANs,"
for more information.
How to Define a MAC-Port-Protocol Binding Rule
To define a MAC-port-protocol binding rule, enter vlan followed by an existing VLAN ID then
binding mac-port-protocol followed by a valid MAC address, a slot/port designation and a protocol
type. For example, the following commands define a MAC-port-protocol binding rule for VLAN 355 and
VLAN 455:
-> vlan 355 binding mac-port-protocol 00:00:da:59:0c:12 3/1 ip-e2
-> vlan 455 binding mac-port-protocol 00:00:20:11:4a:29 4/1 dsapssap 04/04
The first example command specifies that frames received on mobile port 3/1 must contain a source MAC
address of 00:00:da:59:0c:12 and an IP protocol type to qualify for dynamic assignment to VLAN 355.
The second command specifies that frames received on mobile port 4/1 must contain a source MAC
address of 00:00:20:11:4a:29 and a DSAP/SSAP protocol value of 04/04 to qualify for dynamic assign-
ment to VLAN 455.
The following table lists command keywords for specifying a protocol type:
protocol type keywords
ip-e2
ip-snap
ipx-e2
ipx-novell
ipx-llc
ipx-snap
Note that specifying a SNAP protocol type restricts classification of mobile port traffic to the ethertype
value found in the IEEE 802.2 SNAP LLC frame header.
Use the no form of the
ing rule. Note that it is only necessary to enter the rule's MAC address and protocol parameter values to
identify which rule to remove.
-> vlan 455 no binding mac-port-protocol 00:00:20:11:4a:29 dsapssap 04/04
Note that this binding rule type is also supported on AVLANs. See
cated VLANs,"
for more information.
OmniSwitch 6624/6648 Network Configuration Guide
vlan binding mac-ip-port
decnet
appletalk
ethertype
dsapssap
snap
vlan binding mac-port-protocol
Configuring VLAN Rule Definitions
command to remove a MAC-port-IP binding rule. Note
Chapter 18, "Configuring Authenti-
command to remove a MAC-port-protocol bind-
Chapter 18, "Configuring Authenti-
April 2004
page 7-15
Advertisement
Table of Contents
