Mitsubishi Electric FR-E700 Instruction Manual page 13

5 Basic settings
5.1 Simple mode parameter list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
5.1.6
5.1.7
5.1.8
5.2 PU operation mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-20
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.3 External operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-30
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
FR-E700 EC
Overheat protection of the motor by the inverter. . . . . . . . . . . . . . . . . .5-2
When the rated motor frequency is 60Hz (Pr. 3) . . . . . . . . . . . . . . . . .5-4
Increase the starting torque (Pr. 0) . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Limit the maximum and minimum output frequency (Pr. 1, Pr. 2) . . . . .5-7
Change the acceleration/deceleration time (Pr. 7, Pr. 8) . . . . . . . . . . .5-9
Operation mode (Pr. 79) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Large starting torque and low speed torque are necessary
(Advance magnetic flux control, general-purpose
magnetic flux vector control) (Pr. 71, Pr. 80, Pr. 81, Pr. 800) . . . . . .5-12
To exhibit the best performance of the motor performance
(offline auto tuning) (Pr. 9, Pr. 71, Pr. 83, Pr. 84, Pr. 96) . . . . . . . . . .5-15
Set the set frequency to operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-21
Use the digital dial like a potentiometer to perform operation . . . . . . .5-23
Use switches to give the frequency command (multi-speed setting) .5-24
Perform frequency setting by analog voltage input . . . . . . . . . . . . . . .5-26
Perform frequency setting by analog current input . . . . . . . . . . . . . . .5-28
Use the set frequency set by the operation panel (Pr. 79 = 3) . . . . . .5-30
Use switches to give a start command and a frequency command
(multi-speed setting) (Pr. 4 to Pr. 6) . . . . . . . . . . . . . . . . . . . . . . . . . .5-32
Perform frequency setting by analog voltage input . . . . . . . . . . . . . . .5-35
Change the frequency (40Hz) of the maximum value of
potentiometer (at 5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-38
Perform frequency setting by analog current input . . . . . . . . . . . . . . .5-39
Change the frequency (40Hz) of the maximum value of
potentiometer (at 20mA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-41
Contents
IX