D-Link DWS-3160-24TC Cli Reference Manual page 790

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
[down | up] [<uint 0-4294967295> | default] | diffserv_policy [down | up] [policy_name
<name 31> | clear]] | deny_broadcast [enable | disable] | dist_tunnel [enable | disable] |
dot1x [bcast_key_refresh_rate <int 0-86400> | session_key_refresh_rate <int>] | hide_ssid
[enable | disable] | mac_authentication [enable [local | radius] | disable] | radius [accounting
[enable | disable] | use_network_configuration [enable | disable]] | redirect [mode [http |
none | default] | url [<url> | clear]] | security mode [none | static_wep | wep_dot1x |
wpa_enterprise | wpa_personal | default] | ssid <ssid 32> | vlan [<int 1-4094> | default] | wep
[authentication [open_system {shared_key} | shared_key | default] | key [index <int 1-4>
[value <string> | clear] | length [64 | 128 | default] | type [ascii | hex | default]] | tx_key [<int
1-4> | default]] | wpa [ciphers [ccmp {tkip} | tkip | default] | key [value <string> | clear] |
versions [wpa {wpa2} | wpa2 | default]] | wpa2 [key_chching holdtime [<int 1-1440> | default]
| pre_authentication [state [enable | disable] | limit [<int 0-192> | default]]] | ip_tunnel [state
[enable | disable] | subnet <ipaddr> mask <netmask>]]
Parameters
<int 1-64> - Enter the wireless network ID used here. This value must be between 1 and 64.
arp_suppression - Specifies the state of the mode that allows the APs to reduce the number of
broadcasted ARP requests on the wireless interfaces. Reducing broadcasts helps to conserve
power on the wireless clients. The wireless clients that utilize the power-save mode must then
wake up and use more power when they detect broadcasted frames. Enabling this feature
slightly degrades AP packet forwarding performance due to extra packet filtering that takes
place to find DHCP packets and extra processing for ARP request and reply packets.
Networks that do not use IPv4 should not enable this feature.
enable - Specifies that the state of the mode, that allows the APs to reduce the number of
broadcasted ARP requests on the wireless interfaces, will be enabled.
disable - Specifies that the state of the mode, that allows the APs to reduce the number of
broadcasted ARP requests on the wireless interfaces, will be disabled. This is the default
option.
clear - Specifies to restores a network configuration to its default values.
client_qos - Specifies the client QoS parameters that allows the Switch to apply access control
lists (ACLs) and differentiated service (DiffServ) policies to wireless clients, associated with
the AP, and extend the Switch QoS features into the wireless domain.
state - Specifies the state of AP client QoS operation for the network. When enabled, clients
associated to this network may have one or more of the following QoS facilities in effect in
the down and/or up directions: access control, bandwidth limiting, and Differentiated
services (via policy).
enable - Specifies that the state of AP client QoS operation for the network will be enabled.
disable - Specifies that the state of AP client QoS operation for the network will be
disabled. This is the default option.
access_control - Specifies to configure the ACL used by clients associated with this network.
down - Specifies to select the name of the access list, applied to traffic, in the outbound
(down) direction.
up - Specifies to select the name of the access list, applied to traffic, in the inbound (up)
direction.
ip acl_num - Specifies to configure IP-standard or IP-extended type of access list to the
network as a client QoS.
<int 1-199> - Enter the IP ACL numerical value used here. This value must be between
1 and 199.
acl_name - Specifies to configure the IP-name type of access list to the network as a client
QoS.
<name 31> - Enter the IP ACL name value used here. This name can be up to 31
characters long.
ipv6 - Specifies to configure IPv6 type of access list to the network as a client QoS.
acl_name - Specifies to configure the IPv6-name type of access list to the network as a
client QoS.
<name 31> - Enter the IPv6 ACL name used here. This name can be up to 31
786