1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Switch
  5. DWS-1008
  6. Installation manual

D-Link DWS-1008 Installation Manual

8 port 10/100 wireless switch with power ovet ethernet
Hide thumbs Also See for DWS-1008:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Cli Reference Manual

Advertisement

Table of Contents
loading

Related Manuals for D-Link DWS-1008

Summary of Contents for D-Link DWS-1008

  • Page 2: System Requirements

    Rubber Feet (4) Manual and Reference Guide on CD Caution: The DWS-1008 switch has been designed and tested to be installed in an operating ambient temperature of 0° C to +40° C (32° F to 104° F). To reduce the risk of equipment damage, install equipment with consideration to these ambient conditions.

  • Page 3: Hardware Overview

    The serial console port provides a direct management connection to a DWS-1008 switch’s command-line interface (CLI). Ethernet Ports (1-6): The 10/100 Ethernet ports on the DWS-1008 switch provide automatic MDI/MDX, which automatically crosses over the send and receive signals if required. Ports 1-6 also support PoE (Power over Ethernet).

  • Page 4: Installation Overview

    Switch Pin 10/100 Ethernet Cable Wiring Connections on the 10/100 ports require CAT5 cable based on the EIA/TIA-586 standard. The 10/100 Ethernet ports on the DWS-1008 switch provide automatic MDI/MDX, which automatically crosses over the send and receive signals if required.
  • Page 5 The mounting brackets support front mounting only. Warning: Earth grounding is required for a DWS-1008 switch installed in a rack. If you are relying on the rack to provide ground, the rack itself must be grounded with a ground strap to the earth ground.

  • Page 6: Getting Started

    * The Mobility System Software is built-in to the fi rmware on the DWS-1008 switch. No additional software is required. The switch supports two connection modes: •...

  • Page 7: Equipment Rack Installation

    The location areas are marked by X’s and attach the four rubber adhesive feet over the X’s. 3. Turn the switch right-side up, and place the switch in position on the table. Powering On a DWS-1008 Switch Warning: The switch relies on the building’s installation for overcurrent protection.

  • Page 8: Connecting To A Serial Management Console

    LED is steadily glowing green. This indicates normal power supply operation. Connecting to a Serial Management Console Initial confi guration of the DWS-1008 switch requires a connection to the switch’s CLI through the serial console port. To connect a PC to the serial console port: 1.

  • Page 9: Connecting To The Network

    Note: The 10/100 Ethernet ports are confi gured as wired network ports by default. You must change the port type for locally connected DWL-8220AP access points, and for wired end stations that use AAA through the DWS-1008 switch to access the network.
  • Page 10 CLI (Command Line Interface) You can confi gure a switch using the CLI by attaching a PC to the switch’s Console port. After you confi gure the switch for SSH or Telnet access, you also can use these protocols to access the CLI.

  • Page 11: Cli Quickstart Command

    The command automatically places all ports that are not used for directly connected access points into the default VLAN (VLAN 1). Caution: The quickstart command is for confi guration of a new switch only. After prompting you for verifi cation, the command erases the switch’s confi guration before continuing.
  • Page 12 Configuration Configuration (continued) To run the quickstart command: 1. Attach a PC to the DWS-1008 switch’s serial console port. Use the following modem settings: 9600 bps, 8 bits, 1 stop, no parity, hardware fl ow control disabled. 2. Press Enter three times, to display a username prompt (Username:), a...
  • Page 13 IP address separately. • Default route: 10.10.10.1 • Administrative user admin1, with password letmein. The only management access the switch allows by default is CLI access through the serial connection. • System Time and date parameters: •...
  • Page 14 Contacting Technical Support DWS-1008 Install Guide Configuration (continued) 6. Optionally, enable Telnet. DWS-1008-aabbcc# set ip telnet server enable 7. Verify the confi guration changes. DWS-1008-aabbcc# show confi g 8. Save the confi guration changes. DWS-1008-aabbcc# save confi g D-Link Systems, Inc.
  • Page 15 DWS-1008 Install Guide Notes Notes D-Link Systems, Inc.

  • Page 16: Technical Support

    Monday through Friday, 7:30am to 9:00pm EST. World Wide Web http://support.dlink.ca E-mail support@dlink.ca Version 1.0 Revised 12/15/2005 6DWS1008ML01G ©2005 D-Link Systems, Inc. All rights reserved. Trademarks are the property of their respective holders. Software and specifi cations subject to change without notice. D-Link Systems, Inc.

Table of Contents