D-Link DWS-3160-24TC Cli Reference Manual page 110

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
7-1 create egress_access_profile
Description
This command is used to create an egress access list profile. For example, for some hardware, it
may be invalid to Specifies destination IPv6 address and source IPv6 address at the same time.
The user will be prompted for these limitations.
Format
create egress_access_profile profile_id <value 1-4> profile_name <name 1-32> [ethernet
{vlan {<hex 0x0-0x0fff>} | source_mac <macmask 000000000000-ffffffffffff> |
destination_mac <macmask 000000000000-ffffffffffff> | 802.1p | ethernet_type} | ip {vlan
{<hex 0x0-0x0fff>} | source_ip_mask <netmask> | destination_ip_mask <netmask> | dscp |
[icmp {type | code} | igmp {type} | tcp {src_port_mask <hex 0x0-0xffff> | dst_port_mask
<hex 0x0-0xffff> | flag_mask [all | {urg | ack | psh | rst | syn | fin}]} | udp {src_port_mask
<hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} | protocol_id_mask <hex 0x0-0xff>
{user_define_mask <hex 0x0-0xffffffff>}]} | ipv6 {class | source_ipv6_mask <ipv6mask> |
destination_ipv6_mask <ipv6mask> | [tcp {src_port_mask <hex 0x0-0xffff> | dst_port_mask
<hex 0x0-0xffff>} | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} |
icmp {type | code}]}]
Parameters
profile_id - Specifies the index of the egress access list profile.
<value 1-4> - Enter the profile ID used here. This value must be between 1 and 4.
profile_name - The name of the profile must be specified. The maximum length is 32 characters.
<name 1-32> - Enter the profile name used here. This name can be up to 32 characters long.
ethernet - Specifies this is an Ethernet mask.
vlan - (Optional) Specifies a VLAN mask.
<hex 0x0-0x0fff> - Enter the VLAN mask used here.
source_mac - (Optional) Specifies the source MAC mask.
<macmask> - Enter the source MAC mask used here.
destination_mac - (Optional) Specifies the destination MAC mask.
<macmask> - Enter the destination MAC mask used here.
802.1p - (Optional) Specifies 802.1p priority tag mask.
ethernet_type - (Optional) Specifies the Ethernet type mask.
ip - Specifies this is an IPv4 mask.
vlan - (Optional) Specifies a VLAN mask.
<hex 0x0-0x0fff> - Enter the VLAN mask used here.
source_ip_mask - (Optional) Specifies a source IP address mask.
<netmask> - Enter the source network mask used here.
destination_ip_mask - (Optional) Specifies a destination IP address mask.
<netmask> - Enter the destination network mask used here.
dscp - (Optional) Specifies the DSCP mask.
icmp - (Optional) Specifies that the rule applies to ICMP traffic.
type - Specifies the type of ICMP traffic.
code - Specifies the code of ICMP traffic.
igmp - (Optional) Specifies that the rule applies to IGMP traffic.
type - Specifies the type of IGMP traffic.
tcp - (Optional) Specifies that the rule applies to TCP traffic.
src_port_mask - Specifies the TCP source port mask.
<hex 0x0-0xffff> - Enter the TCP source port mask value here.
dst_port_mask - Specifies the TCP destination port mask.
<hex 0x0-0xffff> - Enter the TCP source port mask value here.
flag_mask - (Optional) Specifies the TCP flag field mask.
106