YASKAWA G7 Series Technical Manual page 447

No. Name
Multi-function analog input (termi-
H3-05
nal A3)
H3-06 Gain (terminal A3)
H3-07 Bias (terminal A3)
Multi-function analog input termi-
H3-08
nal A2 function selection
Multi-function analog input termi-
H3-09
nal A2 signal level selection
H3-10 Gain (terminal A2)
H3-11 Bias (terminal A2)
H3-12 Analog input filter time constant
H4-01 Monitor selection (terminal FM)
H4-02 Gain (terminal FM)
H4-03 Bias (terminal FM)
H4-04 Monitor selection (terminal AM)
H4-05 Gain (terminal AM)
H4-06 Bias (terminal AM)
Analog output 1 signal level selec-
H4-07
tion
Analog output 2 signal level selec-
H4-08
tion
H5-01 Station address
H5-02 Communication speed selection
H5-03 Communication parity selection
Stopping method after communi-
H5-04
cation error
Communication error detection
H5-05
selection
H5-06 Send wait time
H5-07 RTS control ON/OFF
H6-01 Pulse train input function selection
H6-02 Pulse train input scaling
H6-03 Pulse train input gain
H6-04 Pulse train input bias
H6-05 Pulse train input filter time
H6-06 Pulse train monitor selection
H6-07 Pulse train monitor scaling
L1-01 Motor protection selection
L1-02 Motor protection time constant
Alarm operation selection during
L1-03
motor overheating
Motor overheating operation selec-
L1-04
tion
Motor temperature input filter time
L1-05
constant
L2-01 Momentary power loss detection
Momentary power loss ridethru
L2-02
time
L2-03 Min. baseblock time
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Table 10.7 User Parameters (Continued)
Factory
Setting No.
Setting
2 L2-04
100.0 L2-05
0.0 L2-06
2 L2-07
0 L2-08
100.0 L3-01
0.0 L3-02
0.03 L3-03
2 L3-04
1.00 L3-05
0.0 L3-06
3 L4-01
0.50 L4-02
0.0 L4-03
0 L4-04
0 L4-05
1F L5-01
3 L5-02
0 L6-01
3 L6-02
1 L6-03
5 L6-04
1 L6-05
0 L6-06
1440 L7-01
100.0 L7-02
0.0 L7-03
0.10 L7-04
2 L8-01
1440 L8-02
1 L8-03
1.0 L8-05
3 L8-07
1 L8-09
0.20 L8-10
0 L8-11
*6
L8-12
0.1
0.5 L8-15
Name
Voltage recovery time
Undervoltage detection level
KEB deceleration time
Momentary recovery time
Frequency reduction gain at KEB
start
Stall prevention selection during
accel
Stall prevention level during accel
Stall prevention limit during accel
Stall prevention selection during
decel
Stall prevention selection during
running
Stall prevention level during run-
ning
Speed agreement detection level
Speed agreement detection width
Speed agreement detection level
(+/-)
Speed agreement detection width
(+/-)
Operation when frequency refer-
ence is missing
Number of auto restart attempts
Auto restart operation selection
Torque detection selection 1
Torque detection level 1
Torque detection time 1
Torque detection selection 2
Torque detection level 2
Torque detection time 2
Forward drive torque limit
Reverse drive torque limit
Forward regenerative torque limit
Reverse regenerative torque limit
Protect selection for internal DB
resistor (Type ERF)
Overheat pre-alarm level
Operation selection after overheat
pre-alarm
Input open-phase protection selec-
tion
Output open-phase protection
selection
Ground protection selection
Cooling fan control selection
Cooling fan control delay time
Ambient temperature
OL2 characteristics selection at
low speeds
User Parameters
Factory
Setting
Setting
0.3
*7
190
0.0
*11
0
100
1
150
50
1
1
160
0.0
2.0
0.0
2.0
0
0
0
0
150
0.1
0
150
0.1
200
200
200
200
0
95
3
0
0
1
0
60
45
1
23
10-