Lcp Keypad; Max Value Of User-Defined Readout; Source For User-Defined Readout; Display Text - Danfoss VLT AutomationDrive FC 302 Programming Manual

Parameter Descriptions
0-30 Unit for User-defined Readout
Option:
[171] lb/in²
[172] in WG
[173] ft WG
3 3
[176] kpsi
[177] MPa
[178] kBar
[180] HP
0-31 Min Value of User-defined Readout
Range:
0 CustomRea-
doutUnit
*

0-32 Max Value of User-defined Readout

Range:
100 Custom-
ReadoutUnit
*

0-33 Source for User-defined Readout

Option:
[105] Torq relate to rated
[143] PID Clamped Output
4-20mA
[240] Default Source
*

0-37 Display Text 1

Range: Function:
0 [0 - Enter a text which can be viewed in the graphical
*
25 ] display by selecting [37] Display Text 1 in
38
VLT
Function:
Function:
[ -999999.99 - This parameter sets the
par. 0-32 minimum value of the custom-
CustomRea- defined readout (occurs at 0
doutUnit] speed). Only possible to set
different from 0 when selecting
a linear unit in
parameter 0-30 Unit for User-
defined Readout. For quadratic
and cubic units, the minimum
value is 0.
Function:
[ par. 0-31 - This parameter sets the
999999.99 maximum value to be shown
CustomRea- when the speed of the motor
doutUnit] has reached the set value for
parameter 4-13 Motor Speed
High Limit [RPM] or
parameter 4-14 Motor Speed
High Limit [Hz] (depends on
setting in parameter 0-02 Motor
Speed Unit).
Function:
Enter the source of the
user-defined readout.
•
Parameter 0-20 Display Line 1.1 Small,
•
Parameter 0-21 Display Line 1.2 Small,
•
Parameter 0-22 Display Line 1.3 Small,
•
Parameter 0-23 Display Line 2 Large, or
•
Parameter 0-24 Display Line 3 Large.
Danfoss A/S © 10/2018 All rights reserved.
®
AutomationDrive FC 301/302
0-38 Display Text 2
Range:
0 [0 -
*
25 ]
0-39 Display Text 3
Range:
0 [0 -
*
25 ]

3.1.5 0-4* LCP Keypad

Enable, disable, and password protect individual keys on
the LCP.
0-40 [Hand on] Key on LCP
Option:
[0] Disabled
[1] Enabled
[2] Password
[3] Hand Off/On When [Hand On] is pressed once, the LCP
[4] Hand Off/On
w. Passw.
[9] Enabled, ref
= 0
0-41 [Off] Key on LCP
Option:
[0] Disabled
[1] Enabled
Function:
Enter a text which can be viewed in the graphical
display by selecting [38] Display Text 2 in
•
Parameter 0-20 Display Line 1.1 Small,
•
Parameter 0-21 Display Line 1.2 Small,
•
Parameter 0-22 Display Line 1.3 Small,
•
Parameter 0-23 Display Line 2 Large, or
•
Parameter 0-24 Display Line 3 Large.
Function:
Enter a text which can be viewed in the graphical
display by selecting [39] Display Text 3 in
•
Parameter 0-20 Display Line 1.1 Small,
•
Parameter 0-21 Display Line 1.2 Small,
•
Parameter 0-22 Display Line 1.3 Small,
•
Parameter 0-23 Display Line 2 Large, or
•
Parameter 0-24 Display Line 3 Large.
Function:
No effect when [Hand On] is pressed. Select [0]
Disabled to avoid accidental start of the
frequency converter in hand-on mode.
The LCP switches to hand-on mode directly
when [Hand On] is pressed.
After pressing [Hand On] a password is
required. If parameter 0-40 [Hand on] Key on
LCP is included in My Personal Menu, define the
password in parameter 0-65 Personal Menu
Password. Otherwise define the password in
parameter 0-60 Main Menu Password.
switches to Off mode. When pressed again, the
LCP switches to hand-on mode.
Same as option [3] Hand Off/On but a
password is required (see option [2] Password).
Function:
Avoids accidental stop of the frequency converter.
MG33MP02