Copy/Save; [Off] Key On Lcp; [Reset] Key On Lcp; Lcp Copy - Danfoss VLT AutomationDrive FC 302 Programming Manual

Parameter Descriptions

0-41 [Off] Key on LCP

Option: Function:
[2] Password Avoids unauthorized stop. If parameter 0-41 [Off]
Key on LCP is included in the Quick Menu, then
define the password in parameter 0-65 Personal
Menu Password.
0-42 [Auto on] Key on LCP
Option: Function:
[0] Disabled Avoids accidental start of the frequency converter
in auto-on mode.
[1] Enabled
[2] Password Avoids unauthorized start in auto-on mode. If
parameter 0-42 [Auto on] Key on LCP is included in
the Quick Menu, then define the password in
parameter 0-65 Personal Menu Password.

0-43 [Reset] Key on LCP

Option: Function:
[0] Disabled No effect when [Reset] is pressed. Avoids
accidental alarm reset.
[1] Enabled
[2] Password Avoids unauthorized resetting. If
parameter 0-43 [Reset] Key on LCP is included in
the Quick Menu, then define the password in
parameter 0-65 Personal Menu Password.
[7] Enabled Resets the frequency converter without setting
without OFF it in Off mode.
[8] Password Resets the frequency converter without setting
without OFF it in Off mode. A password is required when
pressing [Reset] (see option [2] Password).
0-44 [Off/Reset] Key on LCP
Enable or disable the [Off/Reset] key.
Option:
[0] Disabled
[1] Enabled
*
[2] Password
0-45 [Drive Bypass] Key on LCP
Press [Off] and select [0] Disabled to avoid unintended stop of
the frequency converter. Press [Off] and select [2] Password to
avoid unauthorized bypass of the frequency converter. If
parameter 0-45 [Drive Bypass] Key on LCP is included in the Quick
Menu, define the password in parameter 0-65 Personal Menu
Password.
Option:
[0] Disabled
[1] Enabled
*
[2] Password
MG33MP02
Programming Guide

3.1.6 0-5* Copy/Save

Copy parameters from and to the LCP. Use these
parameters for saving and copying set-ups from 1
frequency converter to another.

0-50 LCP Copy

Option:
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[9]
Function:
[10] Delete LCP copy
0-51 Set-up Copy
Option:
[0]
[1]
[2]
Function:
Select to disable the
[3]
key.
Danfoss A/S © 10/2018 All rights reserved.
Function:
NOTICE
This parameter cannot be
adjusted while the motor is
running.
No copy
*
All to LCP Copies all parameters in all set-ups
from the frequency converter memory
to the LCP memory.
All from LCP Copies all parameters in all set-ups
from the LCP memory to the frequency
converter memory.
Size indep. from Copy only the parameters that are
LCP independent of the motor size. The
latter selection can be used to program
several frequency converters with the
same function without disturbing
motor data.
File from MCO to
LCP
File from LCP to
MCO
Data from DYN to
LCP
Data from LCP to
DYN
Safety Par. from
LCP
Use to delete the copy after the
data transfer is complete.
Function:
No copy No function.
*
Copy to set- Copies all parameters in the present
up 1 programming set-up (defined in
parameter 0-11 Edit Set-up) to set-up 1.
Copy to set- Copies all parameters in the present
up 2 programming set-up (defined in
parameter 0-11 Edit Set-up) to set-up 2.
Copy to set- Copies all parameters in the present
up 3 programming set-up (defined in
parameter 0-11 Edit Set-up) to set-up 3.
3 3
39