Parameters For Signals - Danfoss VLT AutomationDrive FC 302 Programming Manual

Parameter Descriptions
8-40 Telegram Selection
Option: Function:
[105] PPO 5
[106] PPO 6
[107] PPO 7
[108] PPO 8
[200] Custom telegram 1 Enables use of freely configurable
telegrams or standard telegrams for
the FC port.
[202] Custom telegram 3

8-41 Parameters for Signals

Option:
[0] None
*
[15] Readout: actual setup
[302] Minimum Reference
[303] Maximum Reference
[312] Catch up/slow Down Value
[321] Touch Target
[322] Master Scale Numerator
[323] Master Scale Denominator
[326] Master Offset
[328] Master Offset Speed Ref
[341] Ramp 1 Ramp Up Time
[342] Ramp 1 Ramp Down Time
[351] Ramp 2 Ramp Up Time
[352] Ramp 2 Ramp Down Time
[380] Jog/Homing Ramp Time
[381] Quick Stop Ramp Time
[411] Motor Speed Low Limit [RPM]
[412] Motor Speed Low Limit [Hz]
[413] Motor Speed High Limit [RPM]
[414] Motor Speed High Limit [Hz]
[416] Torque Limit Motor Mode
[417] Torque Limit Generator Mode
[482] Power Limit Motor Mode
[483] Power Limit Generator Mode
[491] Positive Speed Limit [RPM]
[492] Positive Speed Limit [Hz]
[493] Negative Speed Limit [RPM]
[494] Negative Speed Limit [Hz]
[495] Positive Torque limit
[496] Negative Torque limit
[553] Term. 29 High Ref./Feedb. Value
[558] Term. 33 High Ref./Feedb. Value
[590] Digital & Relay Bus Control
[593] Pulse Out #27 Bus Control
[595] Pulse Out #29 Bus Control
[597] Pulse Out #X30/6 Bus Control
[615] Terminal 53 High Ref./Feedb. Value
[625] Terminal 54 High Ref./Feedb. Value
[653] Term 42 Output Bus Ctrl
[663] Terminal X30/8 Bus Control
[673] Terminal X45/1 Bus Control
MG33MP02
Programming Guide
8-41 Parameters for Signals
Option:
[683]
[748]
[890]
[891]
[1397]
[1398]
[1399]
[1472]
[1473]
[1474]
Function:
[1500]
[1501]
[1502]
[1600]
[1601]
[1602]
[1603]
[1605]
[1606]
[1607]
[1608]
[1609]
[1610]
[1611]
[1612]
[1613]
[1614]
[1615]
[1616]
[1617]
[1618]
[1619]
[1620]
[1621]
[1622]
[1623]
[1624]
[1625]
[1628]
[1630]
[1632]
[1633]
[1634]
[1635]
[1638]
[1639]
[1642]
[1644]
[1645]
[1646]
[1647]
[1648]
Danfoss A/S © 10/2018 All rights reserved.
Terminal X45/3 Bus Control
PCD Feed Forward
Bus Jog 1 Speed
Bus Jog 2 Speed
Alert Alarm Word
Alert Warning Word
Alert Status Word
Legacy Alarm Word
Legacy Warning Word
Leg. Ext. Status Word
Operating hours
Running Hours
kWh Counter
Control Word
Reference [Unit]
Reference %
Status Word
Main Actual Value [%]
Actual Position
Target Position
Position Error
Custom Readout
Power [kW]
Power [hp]
Motor Voltage
Frequency
Motor current
Frequency [%]
Torque [Nm]
Speed [RPM]
Motor Thermal
Thermistor Sensor Temperature
Motor Angle
Torque [%] High Res.
Torque [%]
Motor Shaft Power [kW]
Calibrated Stator Resistance
Torque [Nm] High
Angle Error
DC Link Voltage
Brake Energy /s
Brake Energy Average
Heatsink Temp.
Inverter Thermal
SL Controller State
Control Card Temp.
Service Log Counter
Speed Error [RPM]
Motor Phase U Current
Motor Phase V Current
Motor Phase W Current
Speed Ref. After Ramp [RPM]
Function:
3 3
161