Terminal 18 Digital Input - Danfoss VLT AutomationDrive FC 302 Programming Manual

Parameter Descriptions
parameter 17-90 Absolute Position Mode and
parameter 17-91 Relative Position Mode.
Synchronization mode: High signal locks the
actual follower position to the actual master
position. The follower starts and catches up
with the master. Low signal stops the
synchronization and the follower makes a
controlled stop.
NOTICE
[114] Sync. to
Pos. Mode
This option is available only with
software version 48.XX.
Select positioning in synchronization mode.
NOTICE
[115] Home
Sensor
This option is available only with
software version 48.XX.
Normally open contact for defining the
home position. The function is defined in
parameter 17-80 Homing Function. Available
only at digital inputs 18, 32, and 33.
NOTICE
[116] Home
Sensor Inv.
This option is available only with
software version 48.XX.
Normally closed contact for defining the
home position. The function is defined in
parameter 17-80 Homing Function. Available
only at digital inputs 18, 32, and 33.
NOTICE
[117] Touch
Sensor
This option is available only with
software version 48.XX.
Normally open contact. Serves as a reference
for touch probe positioning. Available only at
digital inputs 18, 32, and 33.
NOTICE
[118] Touch
Sensor
This option is available only with
software version 48.XX.
Normally closed contact. Serves as a
reference for touch probe positioning.
Available only at digital inputs 18, 32, and
33.
NOTICE
[119] Speed
mode
This option is available only with
software version 48.XX.
Select the speed mode when [9] Positioning
or [10] Synchronization is selected in
parameter 1-00 Configuration Mode. Speed
reference is set by reference resource 1 or
fieldbus REF1 relative to
parameter 3-03 Maximum Reference.
[231] Power Limit Select this option to activate the power limit
Mot. function in the motor mode. See parameter
group 4-8* Power Limit.
[232] Power Limit Select this option to activate the power limit
Gen. function in the generating mode. See
parameter group 4-8* Power Limit.
MG33MP02
Programming Guide
[233] Power Limit
Both

5-10 Terminal 18 Digital Input

Option:
[0] No operation
[1] Reset
[2] Coast inverse
[3] Coast and reset inv
[4] Quick stop inverse
[5] DC-brake inverse
[6] Stop inverse
[8] Start
[9] Latched start
[10] Reversing
[11] Start reversing
[12] Enable start forward
[13] Enable start reverse
[14] Jog
[15] Preset reference on
[16] Preset ref bit 0
[17] Preset ref bit 1
[18] Preset ref bit 2
[19] Freeze reference
[20] Freeze output
[21] Speed up
[22] Speed down
[23] Set-up select bit 0
[24] Set-up select bit 1
[26] Precise stop inverse
[27] Precise start, stop
[28] Catch up
[29] Slow down
[34] Ramp bit 0
[35] Ramp bit 1
[40] Latched precise start
[41] Latch prec stop inv
[44] Restart Drive
[51] External Interlock
[55] DigiPot increase
[56] DigiPot decrease
[57] DigiPot clear
[58] DigiPot Hoist
[62] Reset Counter A
[65] Reset Counter B
[70] Mech. Brake Feedb.
[71] Mech. Brake Feedb. Inv.
Danfoss A/S © 10/2018 All rights reserved.
Select this option to activate the power limit
function in both the motor and the
generating mode. See parameter group 4-8*
Power Limit.
Function:
Functions are described in
parameter group 5-1* Digital
Inputs.
Functions are described in
parameter group 5-1* Digital
Inputs.
3 3
103