Sl Controller Event - Danfoss VLT AutomationDrive FC 302 Programming Manual

Parameter Descriptions

13-51 SL Controller Event

Option: Function:
[33] Digital input DI18
[34] Digital input DI19
[35] Digital input DI27
[36] Digital input DI29
[37] Digital input DI32
[38] Digital input DI33
[39] Start command
[40] Drive stopped
[41] Reset Trip
[42] Auto-reset Trip
[43] Ok key [OK] is pressed. Only available on the
graphical LCP.
[44] Reset key [Reset] is pressed. Only available on
the graphical LCP.
[45] Left key [◄] is pressed. Only available on the
graphical LCP.
[46] Right key
[►] is pressed. Only available on the
graphical LCP.
▲
[47] Up key
[ ] is pressed. Only available on the
graphical LCP.
▼
[48] Down key
[ ] is pressed. Only available on the
graphical LCP.
[50] Comparator 4
[51] Comparator 5
[60] Logic rule 4
[61] Logic rule 5
[70] SL Time-out 3
[71] SL Time-out 4
[72] SL Time-out 5
[73] SL Time-out 6
[74] SL Time-out 7
[75] Start command
given
[76] Digital input x30/2
[77] Digital input x30/3
[78] Digital input x30/4
[79] Digital input x46/1
[80] Digital input x46/3
[81] Digital input x46/5
[82] Digital input x46/7
[83] Digital input x46/9
[84] Digital input
x46/11
[85] Digital input
x46/13
[90] ATEX ETR cur. Available if parameter 1-90 Motor
warning Thermal Protection is set to [20] ATEX
ETR or [21] Advanced ETR. If alarm 164,
ATEX ETR cur.lim.alarm is active, the
output is 1.
MG33MP02
Programming Guide
13-51 SL Controller Event
Option:
[91] ATEX ETR cur.
alarm
[92] ATEX ETR freq.
warning
[93] ATEX ETR freq.
alarm
[94] RS Flipflop 0
[95] RS Flipflop 1
[96] RS Flipflop 2
[97] RS Flipflop 3
[98] RS Flipflop 4
[99] RS Flipflop 5
[100] RS Flipflop 6
[101] RS Flipflop 7
[102] Relay 1
[103] Relay 2
[104] Relay 3
[105] Relay 4
[106] Relay 5
[107] Relay 6
[108] Relay 7
[109] Relay 8
[110] Relay 9
[222] Homing Ok
Danfoss A/S © 10/2018 All rights reserved.
Function:
Available if parameter 1-90 Motor
Thermal Protection is set to [20] ATEX
ETR or [21] Advanced ETR]. If alarm
166, ATEX ETR freq.lim.alarm is active,
the output is 1.
Available if parameter 1-90 Motor
Thermal Protection is set to [20] ATEX
ETR or [21] Advanced ETR. If alarm 163,
ATEX ETR cur.lim.warning is active, the
output is 1.
Available if parameter 1-90 Motor
Thermal Protection is set to [20] ATEX
ETR or [21] Advanced ETR. If warning
165, ATEX ETR freq.lim.warning is active,
the output is 1.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
See chapter 3.13.2 13-1* Comparators.
®
X47/VLT Extended Relay Card MCB
113.
®
X47/VLT Extended Relay Card MCB
113.
®
X47/VLT Extended Relay Card MCB
113.
®
X47/VLT Extended Relay Card MCB
113.
®
X34/VLT Relay Card MCB 105.
®
X34/VLT Relay Card MCB 105.
®
X34/VLT Relay Card MCB 105.
NOTICE
This option is available only with
software version 48.20 and
newer.
Homing is completed with the
selected homing function
(parameter 17-80 Homing Function).
3 3
185