ABB ACS880 Firmware Manual page 403

No. Name/Value
93.11 Absolute position
source
93.11 Excitation signal
amplitude
93.12 Speed calculation
mode
93.12 Zero pulse enable
93.12 Resolver polepairs
93.13 Position estimation
enable
93.13 Position data width
93.14 Speed estimation
enable
93.14 Revolution data
width
93.15 Transient filter
93.17 Accepted pulse freq
of encoder 2
93.21 Encoder cable fault
mode
93.23 Maximum pulse
waiting time
93.24 Pulse edge filtering
93.25 Pulse
overfrequency
function
93.30 Serial link mode
93.31 EnDat calc time
93.32 SSI cycle time
93.33 SSI clock cycles
93.34 SSI position msb
93.35 SSI revolution msb
93.36 SSI data format
93.37 SSI baud rate
ghv Vertriebs-GmbH | Am Schammacher Feld 47 | 85567 Grafing | Telefon + 49 80 92 81 89 0 | info@ghv.de | www.ghv.de
Description
(Visible when an absolute encoder is selected)
See parameter 92.11 Absolute position
(Visible when a resolver is selected)
See parameter 92.11 Excitation signal
(Visible when a TTL, TTL+ or HTL encoder is selected)
See parameter 92.12 Speed calculation
(Visible when an absolute encoder is selected)
See parameter 92.12 Zero pulse
(Visible when a resolver is selected)
See parameter 92.12 Resolver
(Visible when a TTL, TTL+ or HTL encoder is selected)
See parameter 92.13 Position estimation
(Visible when an absolute encoder is selected)
See parameter 92.13 Position data
(Visible when a TTL, TTL+ or HTL encoder is selected)
See parameter 92.14 Speed estimation
(Visible when an absolute encoder is selected)
See parameter 92.14 Revolution data
(Visible when a TTL, TTL+ or HTL encoder is selected)
See parameter 92.15 Transient
(Visible when parameter 93.01 Encoder 2 type
HTL 2)
See parameter 92.17 Accepted pulse freq of encoder
(Visible when a TTL, TTL+ or HTL encoder is selected)
See parameter 92.21 Encoder cable fault
(Visible when parameter 93.01 Encoder 2 type
See parameter 92.23 Maximum pulse waiting
(Visible when parameter 93.01 Encoder 2 type
See parameter 92.24 Pulse edge
(Visible when parameter 93.01 Encoder 2 type
See parameter 92.25 Pulse overfrequency
(Visible when an absolute encoder is selected)
See parameter 92.30 Serial link
(Visible when an absolute encoder is selected)
See parameter 92.31 EnDat max calculation
(Visible when an absolute encoder is selected)
See parameter 92.32 SSI cycle
(Visible when an absolute encoder is selected)
See parameter 92.33 SSI clock
(Visible when an absolute encoder is selected)
See parameter 92.34 SSI position
(Visible when an absolute encoder is selected)
See parameter 92.35 SSI revolution
(Visible when an absolute encoder is selected)
See parameter 92.36 SSI data
(Visible when an absolute encoder is selected)
See parameter 92.37 SSI baud
Parameters 403
source.
amplitude.
mode.
enable.
polepairs.
enable.
width.
enable.
width.
filter.
= HTL 1 or
1.
mode.
= TTL or HTL)
time.
= HTL)
filtering.
= HTL)
function.
mode.
time.
time.
cycles.
msb.
msb.
format.
rate.
Def/FbEq16
None
4.0 V
Auto rising
Disable
1
Enable
0
Disable
0
4880 Hz
0 kHz
A, B
4 ms
No filtering
Fault
Initial position
50 ms
100 us
2
1
1
Binary
100 kBit/s