ABB ACS880 Firmware Manual page 169

No. Name/Value
Input
14.16 DIO2 output source
14.17 DI2 ON delay
0.00 ... 3000.00 s
14.17 DIO2 ON delay
0.00 ... 3000.00 s
14.18 DI2 OFF delay
0.00 ... 3000.00 s
14.18 DIO2 OFF delay
0.00 ... 3000.00 s
14.19 DIO3 function
Output
Input
14.19 AI supervision
function
No action
Fault
Warning
Last speed
Speed ref safe
ghv Vertriebs-GmbH | Am Schammacher Feld 47 | 85567 Grafing | Telefon + 49 80 92 81 89 0 | info@ghv.de | www.ghv.de
Description
DIO2 is used as a digital input.
(Visible when 14.01 Module 1 type
Selects a drive signal to be connected to digital input/output
DIO2 when parameter 14.14 DIO2 function
For the available selections, see parameter
source.
(Visible when 14.01 Module 1 type
Defines the activation delay for digital input DI2. See
parameter 14.12 DI1 ON delay.
Activation delay for DI2.
(Visible when 14.01 Module 1 type
Defines the activation delay for digital input/output DIO2. See
parameter 14.12 DIO1 ON
Activation delay for DIO2.
(Visible when 14.01 Module 1 type
Defines the deactivation delay for digital input DI2. See
parameter 14.12 DI1 ON delay.
Deactivation delay for DI2.
(Visible when 14.01 Module 1 type
Defines the deactivation delay for digital input/output DIO2.
See parameter 14.12 DIO1 ON
Deactivation delay for DIO2.
(Visible when 14.01 Module 1 type
Selects whether DIO3 of the extension module is used as a
digital input or output.
DIO3 is used as a digital output.
DIO3 is used as a digital input.
(Visible when 14.01 Module 1 type
Selects how the drive reacts when an analog input signal
moves out of the minimum and/or maximum limits specified
for the input.
The inputs and the limits to be observed are selected by
parameter 14.20 AI supervision
No action taken.
Drive trips on 80A0 AI supervision.
Drive generates an A8A0 AI supervision
Drive generates a warning
the speed (or frequency) to the level the drive was operating
at. The speed/frequency is determined on the basis of actual
speed using 850 ms low-pass filtering.
WARNING! Make sure that it is safe to continue
operation in case of a communication break.
Drive generates a warning
speed to the speed defined by parameter
safe (or 28.41 Frequency ref safe
is being used).
WARNING! Make sure that it is safe to continue
operation in case of a communication break.
= FIO-01 or FIO-11)
is set to Output.
14.11 DIO1 output
= FDIO-01)
= FIO-01 or FIO-11)
delay.
= FDIO-01)
= FIO-01 or FIO-11)
delay.
= FIO-01)
= FIO-11 or FAIO-01)
selection.
warning.
(A8A0 AI supervision) and freezes
(A8A0 AI supervision) and sets the
22.41 Speed ref
when frequency reference
Parameters 169
Def/FbEq16
1
Not
energized
0.00 s
10 = 1 s
0.00 s
10 = 1 s
0.00 s
10 = 1 s
0.00 s
10 = 1 s
Input
0
1
No action
0
1
2
3
4