Siemens 6RA7086-6KS22 Operating Instructions Manual page 622

Parameter list
PNU Description
U698 Binector selection for binary outputs of SCI
(2698) Selection of binectors whose states are output via the binary outputs of the
SCIs
i001: Binector selection for SCI slave1, binary output 1
(Z135)
i002: Binector selection for SCI slave1, binary output 2
(Z136)
i003: Binector selection for SCI slave1, binary output 3
(Z145)
i004: Binector selection for SCI slave1, binary output 4
(Z146)
i005: Binector selection for SCI slave1, binary output 5
i006: Binector selection for SCI slave1, binary output 6
i007: Binector selection for SCI slave1, binary output 7
i008: Binector selection for SCI slave1, binary output 8
i009: Binector selection for SCI slave1, binary output 9
i010: Binector selection for SCI slave1, binary output 10
i011: Binector selection for SCI slave1, binary output 11
i012: Binector selection for SCI slave1, binary output12
i013: Binector selection for SCI slave2, binary output 1
i014: Binector selection for SCI slave2, binary output 2
i015: Binector selection for SCI slave2, binary output 3
i016: Binector selection for SCI slave2, binary output 4
i017: Binector selection for SCI slave2, binary output 5
i018: Binector selection for SCI slave2, binary output 6
i019: Binector selection for SCI slave2, binary output 7
i020: Binector selection for SCI slave2, binary output 8
i021: Binector selection for SCI slave2, binary output 9
i022: Binector selection for SCI slave2, binary output 10
i023: Binector selection for SCI slave2, binary output 11
i024: Binector selection for SCI slave2, binary output12
n699 Display of SCB1/SCI process data
(2699) All values in hexadecimal representation
i001: SCI slave1, binary inputs
(Z130) i002: SCI slave1, analog input1
(Z131) i003: SCI slave1, analog input2
(Z135) i004: SCI slave1, analog input3
(Z136) i005: SCI slave2, binary inputs
(Z140) i006: SCI slave2, analog input1
(Z141) i007: SCI slave2, analog input2
(Z145) i008: SCI slave2, analog input3
(Z146) i009: SCI slave1, binary outputs
(Z150) i010: SCI slave1, analog output1
(Z151) i011: SCI slave1, analog output2
(Z155) i012: SCI slave1, analog output3
(Z156) i013: SCI slave2, binary outputs
i014: SCI slave2, binary outputs
i015: SCI slave2, analog output2
i016: SCI slave2, analog output3
11.84 Configuration of supplementary boards in board locations 2 and 3
U710 Initialize link to supplementary boards
(2710)
i001 Initialization of 1
*
letter)
(Z110)
i002 Initialization of 2
(Z111)
letter
Settings:
0 The link to supplementary boards is re-initialized. After the
configuration parameters for supplementary boards have been
changed, U710 must be set to 0 so that the new settings can
take effect.
The parameter is then set automatically to 1.
Note: Data transmission is interrupted while initialization is in
1 Deactivated
11-158
st
communications board (in slot with lower ID
nd
communications board (in slot with higher ID
progress.
Value range
[Unit]
Steps
[SW 1.9 and later] All binector numbers
1
[SW 1.9 and later]
0 to 1
1
SIMOREG DC Master
05.05
No. indices See
Factory Change
setting (Access /
Type Status)
Ind:24 P052 = 3
FS= 0 P051 =40
Type L2 on-line
Ind:16 P052 = 3
Type L2 P051 =40
on-line
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: O2 Offline
SIEMENS AG 6RX1700-0AD76
Operating Instructions