Siemens 6RA7086-6KS22 Operating Instructions Manual page 517

05.05
PNU Description
P471 Source for manual/automatic switchover
*
Selection of binector to control "Manual/automatic switchover"
BDS
("0" state = manual).
(G126) 0 = binector B0000
1 = binector B0001
etc.
P472 Source for set motorized potentiometer
*
Selection of binector to control "Set motorized potentiometer"
BDS
("0" to "1" transition = set motorized potentiometer).
(G126) 0 = binector B0000
1 = binector B0001
etc.
P473 Storage of output value
*
0 No storage of output value:
FDS
The output is set to 0 in all operating states of >o5.
The starting point after ON is determined by P467 (MOP starting
(G126)
value).
1 Non-volatile storage of output value:
The output value remains stored in all operating states and after
voltage disconnection or failure. The last value stored is output
again after voltage recovery/reconnection.
11.26 Oscillation
Function:
Parameters P480 to P483 define the waveshape of a rectangular signal (oscillation setpoint K0203). The value set in P480 determines the
signal level for the time period set in P481 and the value set in P482 the signal level for the time period set in P483.
Oscillation: Selected in P485. The free-running rectangular signal is switched through to the output K0208.
P480 Oscillation setpoint 1
FDS
(G128)
P481 Oscillation time 1
FDS
(G128)
P482 Oscillation setpoint 2
FDS
(G128)
P483 Oscillation time 2
FDS
(G128)
P484 Source for standard setpoint
*
Selection of connector to be injected as the output value when the
FDS
"Oscillation" function is not selected
(G128)
0 = connector K0000
1 = connector K0001
etc.
P485 Source for oscillation selection
*
Selection of binector to control activation of the "Oscillation" function
BDS
(log. "1" state = oscillation active)
(G128)
0 = binector B0000
1 = binector B0001
etc.
SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Value range No. indices
[Unit] Factory
Steps setting
Type
All binector numbers Ind: 2
1 FS=0
Type: L2
All binector numbers Ind: 2
1 FS=0
Type: L2
0 to 1 Ind: 4
1 FS=0
Type: O2
-199.9 to 199.9 Ind: 4
[%] FS=0,5
0.1% of maximum Type: I2
speed
0.1 to 300.0 Ind: 4
[s] FS=0.1
0.1s Type: O2
-199.9 to 199.9 Ind: 4
[%] FS=-0,4
0.1% of maximum Type: I2
speed
0.1 to 300.0 Ind: 4
[s] FS=0.1
0.1s Type: O2
All connector Ind: 4
numbers FS=209
1 Type: L2
All binector numbers Ind: 2
1 FS=0
Type: L2
Parameter list
See
Change
(Access /
Status)
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
11-53