Siemens 6RA7086-6KS22 Operating Instructions Manual page 541

05.05
PNU Description
P714 Source for selection of sign reversal at "Analog selectable input 1"
*
Selection of binector to control sign reversal at the analog input ("1" state
= reverse sign)
(G113)
0 = binector B0000
1 = binector B0001
etc.
P715 Filtering time for "Analog selectable input 1"
Note: Hardware filtering of approximately 1 ms is applied as standard.
(G113)
P716 Source for enabling of "Analog selectable input 1"
*
Selection of binector to control enabling of the analog input ("1" state =
enabled)
(G113)
0 = binector B0000
1 = binector B0001
etc.
P717 Resolution of "Analog selectable input 1"
*
See P707
(G113)
Analog input terminals 8 / 9 (analog selectable input 2)
P721 Normalization of "Analog selectable input 2"
This parameter specifies the percentage value which is generated for an
FDS
input voltage of 10V (or an input current of 20mA) at the analog input.
(G114) The following generally applies:
For voltage input:
[%] =
P 721 10 V
With current input:
[%] =
P 721 20
P722 Offset for "Analog selectable input 2"
(G114)
P723 Mode of signal injection at "Analog selectable input 2"
*
0 = Injection of signal with sign
1 = Injection of absolute value of signal
(G114)
2 = Injection of signal with sign, inverted
3 = Injection of absolute value of signal, inverted
P724 Source for selection of sign reversal at "Analog selectable input 2"
*
Selection of binector to control sign reversal at the analog input ("1" state
= reverse sign)
(G114)
0 = binector B0000
1 = binector B0001
etc.
P725 Filtering time for "Analog selectable input 2"
Note: Hardware filtering of approximately 1 ms is applied as standard.
(G114)
P726 Source for enabling of "Analog selectable input 2"
*
Selection of binector to control enabling of the analog input ("1" state =
enabled)
(G114)
0 = binector B0000
1 = binector B0001
etc.
SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Y
∗
X .. Input voltage in volts
X
Y .. % value which is generated for input
voltage X
Y
∗
X .. Input current in mA
mA
X
Y .. % value which is generated for input
current X
Value range No. indices
[Unit] Factory
Steps setting
Type
All binector numbers Ind: None
1 FS=0
Type: L2
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
All binector numbers Ind: None
1 FS=1
Type: L2
10 to 14 Ind: None
[Bit] FS=12
1 bit Type: O2
-1000.0 to 1000.0 Ind: 4
[%] FS=100.0
0.1% Type: I2
-200.00 to 199.99 Ind: None
[%] FS=0.00
0.01% Type: I2
0 to 3 Ind: None
1 FS=0
Type: O2
All binector numbers Ind: None
1 FS=0
Type: L2
0 to 10000 Ind: None
[ms] FS=0
1ms Type: O2
All binector numbers Ind: None
1 FS=1
Type: L2
Parameter list
See
Change
(Access /
Status)
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Offline
P052 = 3
P051 = 40
Online
P052 = 3
P051 = 40
Offline
11-77