Siemens 6RA7086-6KS22 Operating Instructions Manual page 473

05.05
PNU Description
r012 Motor temperature
Display of motor temperature when a KTY 84 temperature sensor is
(G185) connected (P490.x=1).
A value of "0" is always output in r012 when a PTC thermistor or no
temperature sensor is installed.
i001: Motor temperature 1 (sensor at terminals 22 / 23)
i002: Motor temperature 2 (sensor at terminals 204 / 205)
r013 Heatsink temperature
Display of heatsink temperature
r014 Temperature rise
i001: Calculated motor temperature rise (see P114)
i002: Calculated thyristor temperature rise (see P075)
r015 Display of line voltage (armature)
(generated as arithmetic rectification average, RMS value display applies to
sinusoidal voltage, average over 3 line-to-line voltages)
r016 Display of line voltage (field)
(generated as arithmetic rectification average, RMS value display applies to
sinusoidal voltage)
r017 Display of line frequency
r018 Display of firing angle (armature)
(G163)
r019 Display of actual armature current
The internal actual armature current value is displayed (arithmetic average
(G162)
over the last 6 current peaks in each case)
r020 Display of the absolute value of armature current setpoint
(G162)
r021 Display of torque setpoint after torque limitation
∧ 0.1% of rated motor torque (=rated motor armature current
=
Steps: 1
(G160)
(P100) * magnetic flux at rated motor field current (P102))
r022 Display of torque setpoint before torque limitation
∧ 0.1% of rated motor torque (=rated motor armature current
=
Steps: 1
(G160)
(P100) * magnetic flux at rated motor field current (P102))
r023 Display of speed controller setpoint/actual value deviation
(G152)
r024 Display of actual speed value from pulse encoder
(G145)
r025 Display of actual speed controller value
(G151)
r026 Display of speed controller setpoint
(G152)
r027 Display of ramp-function generator output
(G136)
r028 Display of ramp-function generator input
(G136)
r029 Display of main setpoint before limitation
(G135)
r034 Display of firing angle (field)
(G166)
r035 Display of field current controller actual value
(G166)
SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Value range No. indices
[Unit] Factory
Steps setting
Type
-58 to +318 Ind: 2
[°C] Type: I2
1°C
-47 to +200 Ind: None
[°C] Type: I2
1°C
0.0 to 200.0 Ind: 2
[%] Type: O2
0.1%
0.0 to 2800.0 Ind: None
[V] Type: O2
0.1V
0.0 to 800.0 Ind: None
[V] Type: O2
0.1V
0.00 to 120.00 Ind: None
[Hz] Type: O2
0.01Hz
0.00 to 180.00 Ind: None
[degrees] Type: O2
0.01degrees
-400.0 to 400.0 Ind: None
[% of P100] Type: I2
0.1% of P100
0.0 to 300.0 Ind: None
[% of P100] Type: I2
0.1% of P100
-400.0 to 400.0 Ind: None
[%] Type: I2
0.1% (see column on
left)
-400.0 to 400.0 Ind: None
[%] Type: I2
0.1% (see column on
left)
-200.00 to 199.99 Ind: None
[%] Type: I2
0.01%
-200.00 to 199.99 Ind: None
[%] Type: I2
0.01%
-200.0 to 199.99 Ind: None
[%] Type: I2
0.01%
-200.0 to 199.99 Ind: None
[%] Type: I2
0.01%
-200.00 to 199.99 Ind: None
[%] Type: I2
0.01%
-200.00 to 199.99 Ind: None
[%] Type: I2
0.01%
-200.00 to 199.99 Ind: None
[%] Type: I2
0.01%
0.00 to 180.00 Ind: None
[degrees] Type: O2
0.01degrees
0.0 to 199.9 Ind: None
[% of P102] Type: O2
0.1% of P102
Parameter list
See
Change
(Access /
Status)
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
P052 = 3
11-9