Page 1
Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications...
Page 3
Safety information Introduction Components for marine applications SINAMICS Referencing the standard documentation of the components Using SINAMICS G120 / G120C / Presentation of the "PM240" S120 Blocksize converters in system being considered marine applications System configuration for Application Manual marine applications...
Page 4
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
Integration of the components in the cabinet ................27 Operator panel installed in the cabinet doors ................. 29 Cooling - control cabinet ventilation ..................30 External auxiliary power supply ....................31 Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 6
Table of contents Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
• Always secure the Power Modules when installing or removing by securely attaching them to crane hooks. • Wear your personal protection equipment (e.g. safety shoes, gloves). Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 8
Safety information Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
However, marine-specific operating conditions require restrictions and/or additional measures, which are explained in this Manual. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 10
Introduction Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
160 / 200 / 250 --- / C3 The article numbers are completely listed in the following table. Other Power Modules are not considered. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
In marine applications, CU230P-2 and CU240E-2 can be plugged directly onto PM240-2 Power Modules of frame size FSA, FSB, or FSC. The article numbers are completely listed in the following table. Other Control Units are not considered. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
→ Download (https://support.industry.siemens.com/cs/ww/en/view/109767180) ● Equipment Manual "SINAMICS S120 AC Drive", 6SL3097-5AL00-0AP0 (02/2018) → Download (https://support.industry.siemens.com/cs/ww/en/view/109757057) The most recent edition of each manual is the valid version. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 20
Referencing the standard documentation of the components Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Note Note on G120 and G120C For marine applications, an optional operator panel must usually be installed in the door of the control cabinet. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 22
Presentation of the "PM240" system being considered Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
The system configuration specifically for marine applications is shown in the following sketch. The components must be installed in a control cabinet or in the control cabinet door. Figure 6-1 System configuration for marine applications Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 24
System configuration for marine applications Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
IEC 60533. The precondition here is that the devices are installed in a control cabinet. An optional operator panel (BOP-2, IOP-2) must be installed in the control cabinet doors. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 26
The actual contract defines the IP degree of protection according to IEC 60529. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
(Page 17)". In addition, when used on board marine vessels, the following should also be carefully observed (either in addition or as deviation). Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
The following diagrams show as example an implementation based on the Rittal TS8 control cabinet system equipped with Rittal Earthquake Kit and additional reinforcing measures for marine applications. Figure 8-1 Reinforced control cabinet design Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
(e.g. CU320-2) is connected using "DRIVE-CLiQ". Figure 8-2 Control cabinet with integrated Power Module, frame size FSG, and an integrated, separately installed Control Unit Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
Page 30
• Power Modules, frame sizes FSD, FSE, FSF and FSG, should be arranged centered (widthwise) in the control cabinet. • The drilling patterns for the mounting plate can be taken from the standard documentation. Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
The door mounting kit with Article No. 6SL3256-0AP00-0JA0 is available for this purpose. An IP55 degree of protection can be achieved. Figure 8-4 Control cabinet with installed operator panel Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
The air must be discharged at the top in the cabinet doors or in the roof section. Air intake and/or air discharge locations should be equipped with filters corresponding to the IP degree of protection required. Figure 8-5 Cabinet ventilation Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...
This switched-mode power supply must comply with interference immunity requirements as laid down in IEC 60533 and those laid down in IACS "Requirements concerning ELECTRICAL INSTALLATIONS". Using SINAMICS G120 / G120C / S120 Blocksize converters in marine applications Application Manual, 11/2019, A5E48346362A...