Siemens 6RA7086-6KS22 Operating Instructions Manual page 537

05.05
PNU Description
P684 Source for control word 2, bit24
*
(0=n controller speed droop disabled, 1=enabled)
BDS
(G181)
P685 Source for control word 2, bit25
*
(0=n controller disabled, 1=n controller enabled)
BDS
(G181)
P686 Source for control word 2, bit26
*
(0=external fault 2, 1=no external fault 2)
BDS
(G181)
P687 Source for control word 2, bit27
*
(0=master drive, speed control, 1=slave drive, torque control)
BDS
(G181)
P688 Source for control word 2, bit28
*
(0=external alarm 1, 1=no external alarm 1)
BDS
(G181)
P689 Source for control word 2, bit29
*
(0=external alarm 2, 1=no external alarm 2)
BDS
(G181)
P690 Source for control word 2, bit30
*
(0=select Bico data set 1, 1=select Bico data set 2)
(G181)
P691 Source for control word 2, Bit31
*
Main contactor checkback signal:
BDS
(0 = main contactor dropped out, 1 = main contactor picked up)
(G181)
This control input is intended as a means of looping an auxiliary contact of
the main contactor into the device control.
During the Power ON routine, this signal must switch to "1" within the time
period set in P095. If it does not, or it disappears during operation, fault
message F004 with fault value 6 is activated.
P691 = 0: Bit 31 of control word 2 is inoperative.
(This setting of P691 is always active, regardless of whether
control word 2 is input in word mode [P649 = 9] or bit mode
[P649 <> 9])
P691 = 1: Bit 31 of control word 2 is inoperative.
(This setting of P691 is active only when control word 2 is input
in bit mode, i.e. when P649 <> 9)
11.37 Further configuring measures
P692 Source for selection of injection of standstill field
*
Selection of binector to control injection of the standstill field ("0" state =
BDS
inject standstill field)
(G166)
Note: The delay time set in P258 is not effective when this function is
active.
0 = binector B0000
1 = binector B0001
etc.
P693 Source for selection of enabling command for EMF controller
*
Selection of binector which is to control enabling of the EMF controller
BDS
0 = binector B0000
(G165)
1 = binector B0001
etc.
SIEMENS AG 6RX1700-0AD76
SIMOREG DC Master Operating Instructions
Value range
[Unit]
Steps
All binector numbers
1
All binector numbers
1
All binector numbers
1
All binector numbers
1
All binector numbers
1
All binector numbers
1
All binector numbers
1
[SW 1.8 and later] All binector numbers
1
All binector numbers
1
All binector numbers
1
Parameter list
No. indices See
Factory Change
setting (Access /
Type Status)
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=0 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 Offline
Ind: None P052 = 3
FS=0 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=0 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=0 P051 = 40
Type: L2 Offline
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: L2 Offline
11-73