Manual Transmission Oil Outlet Hose-Renew; Manual Transmission Oil Inlet Hose-Renew - Aston Martin V8 Vantage Workshop Manual

6. Disconnect oil cooler pipes and remove oil cooler (see
Fig. 2).
7. Install plugs in oil cooler and pipe connections.
Installation
1. Clean oil cooler, connections and mating face on
subframe.
2. Remove plugs, position oil cooler and connect oil cooler
pipes (do not tighten at this stage).
3. Install oil cooler and tighten nuts (x4).
4. Tighten pipe unions.
5. Top-up transaxle oil level.
6. Remove drain container.
7. Install rear exhaust silencer heatshield (see Workshop
Manual procedure 02.06.AG Heatshield - Exhaust
Silencer - Renew).
8. Lower vehicle on ramp.
Manual Transmission Oil Outlet Hose-
Renew
Repair Operation Time (ROT)
Item
Manual Transmission Oil Outlet Hose-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear exhaust silencer heatshield (see Workshop
Manual procedure 02.06.AG Heatshield - Exhaust
Muffler - Renew).
3. Release transaxle breather hose from oil cooler pipe.
4. Remove bolt, nuts (x2),insulating washers (x2) and plain
washer securing outlet hose brackets to body.
5. Position container to collect oil spillage.
6. Loosen union and remove hose from oil cooler.
7. Loosen union and remove oil cooler hose from transaxle
and collect hose.
1. Plug oil cooler and transaxle pipe connections.
October 2005
Fig. 2
Code
07.02.FD
Workshop Manual
Transmission Cooling (07.02)
Installation
1. Clean hose connections and remove plugs.
2. Position hose, align brackets, install insulating washers
(x2) and plain washer.
3. Install and tighten bolt and nuts (x2) to correct torque.
4. Connect and tighten hose unions to correct torque.
5. Remove drain container.
6. Install transaxle breather hose clip to oil cooler pipe.
7. Install rear exhaust silencer heatshield (see Workshop
Manual procedure 02.06.AG Heatshield - Exhaust
Muffler - Renew).
8. Lower vehicle on ramp.
Manual Transmission Oil Inlet Hose-
Renew
Repair Operation Time (ROT)
Item
Manual Transmission Oil Inlet Hose-
Renew
Removal
1. Raise vehicle on ramp.
2. Remove rear exhaust silencer heatshield (see Workshop
Manual procedure 02.06.AG Heatshield - Exhaust
Muffler - Renew).
3. Release transaxle breather hose from oil cooler pipe.
4. Remove bolt and nuts (x2) that secure inlet hose
brackets to body.
5. Collect pipe insulating washers (x2) and plain washer.
6. Position container to collect oil spillage.
7. Loosen union and remove hose from oil cooler.
8. Loosen union and remove oil cooler hose from transaxle
and collect hose.
1. Plug oil cooler and transaxle pipe connections.
Installation
1. Clean hose connections and remove plugs.
2. Position hose, align brackets, install insulating washers
and plain washer.
3. Install and tighten bolt and nuts (x2) to correct torque.
4. Connect and tighten hose unions to correct torque.
5. Remove drain container.
6. Install transaxle breather hose clip to oil cooler pipe.
7. Install rear exhaust silencer heatshield (see Workshop
Manual procedure 02.06.AG Heatshield - Exhaust
Muffler - Renew)
8. Lower vehicle on ramp.
Transmission (07.00)
Code
07.02.FE
7-1-3