Battery Conditioner-Renew; Jump Start Terminal-Renew; Battery To Ground Cable Assembly-Renew; Battery To Battery Disconnect Switch Cable Assembly-Renew - Aston Martin V8 Vantage Workshop Manual

10. Position power support bracket, install bolt, torque
tighten bolt and nuts (x2).
11. Install carpet - RH side luggage compartment. (see
Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew).

Battery Conditioner-Renew

Repair Operation Time (ROT)
Item
Battery Conditioner-Renew
Removal
1. Disconnect vehicle battery.
2. Remove carpet - RH side luggage compartment. (see
Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew).
3. Remove tyre sealant bottle.
4. Remove mobility kit from storage rack.
5. Remove bolt, loosen nuts (x2), power socket bracket.
6. Slide luggage compartment fusebox rearwards, release
from mounting bracket.
7. Release terminal cover, remove nut securing main
battery lead to fusebox.
8. Release harness clips (x2) from power socket bracket.
9. Disconnect harness multiplug, battery conditioner.
10. Remove screws (x2), battery conditioner to power
socket bracket. Remove battery conditioner.
Installation
1. Install battery conditioner, install and tighten screws
(x2).
2. Connect multiplug, battery conditioner.
3. Install harness clips (x2) on power socket bracket.
4. Position main battery cable, install and torque tighten
nut, install terminal cover.
5. Install fusebox in mounting bracket.
6. Install harness clips (x2) on power socket bracket.
7. Position power socket bracket, install bolt. torque
tighten bolt and nuts (x2).
8. Install mobility kit.
9. Install tyre sealant bottle.
10. Install carpet - RH side luggage compartment. (see
Workshop Manual procedure 01.05.FB Carpet
Assembly - Luggage Compartment - Side - RH - Renew).
11. Connect vehicle battery.

Jump Start Terminal-Renew

Repair Operation Time (ROT)
Item
Jump Start Terminal-Renew
Removal
1. Disconnect vehicle battery.
October 2005
2. Remove nuts (x2), securing jump start terminal to
mounting bracket.
3. Remove nut securing battery cable to jump start
terminal. Release cable, remove terminal.
Installation
1. Clean jump start terminal and cable connection.
2. Position jump start terminal, connect cable, install and
torque tighten nut.
Code
3. Position jump start terminal to mounting bracket, install
14.01.DL
and torque tighten nuts (x2).
4. Connect vehicle battery.
Battery to Ground Cable Assembly-
Renew
Repair Operation Time (ROT)
Item
Battery to Ground Cable Assembly-
Renew
Removal
1. Power drivers seat fully forward.
2. Remove rear compartment cover.
3. Loosen and disconnect battery earth (negative) terminal.
4. Remove nut securing battery earth cable to body stud.
Remove earth cable.
Installation
1. Clean battery earth terminal and body stud.
2. Install battery earth cable to body stud, install and
torque tighten nut.
3. Position earth lead on battery terminal (negative), torque
tighten terminal nut.
4. Install rear compartment cover.
5. Power drivers seat to original position.
Battery to Battery Disconnect Switch
Cable Assembly-Renew
Repair Operation Time (ROT)
Item
Battery to Battery Disconnect Switch
Cable Assembly-Renew
Removal
1. Power drivers seat fully forward.
2. Remove rear compartment cover.
3. Disconnect vehicle battery.
4. Remove panel assembly - quarter trim middle - RH (see
Workshop Manual procedure 01.05.CT Panel Assembly
Code
- Quarter Trim Middle Section - RH - Renew).
14.01.EA
5. Release rear carpet studs (x2), move carpet aside.
6. Remove screws (x2), battery compartment cover to
support rail.
Workshop Manual
Battery System (14.01)
Power Supply (14.00)
Code
14.01.EB
Code
14.01.EF
14-1-5