Rh/Lh Door Trim Upper Veneer Panel-Renew; Lh Door Trim Upper Panel-Renew; Rh/Lh Interior Door Assembly Handle And Armrest-Renew; Rh/Lh Door Pocket Assembly-Renew - Aston Martin V8 Vantage Workshop Manual

Interior Trim (01.05)
Body System (01.00)
6. Remove door trim panel bolts (x5).
7. Lift trim out and up to release trim from door frame and
disconnect multiplugs (x2).
Installation
1. Position door trim panel and connect harness
multiplugs.
2. Place trim over top of retaining clips and pull out and
down to fit panel.
3. Install the door trim panel screws (x5).
4. Install screw (x1) trim panel to top front of door frame.
5. Connect release cable and position door handle trim
plate.
6. Install door handle (Bolts x2).
7. Connect vehicle battery.
RH/LH Door Trim Upper Veneer Panel-
Renew
Repair Operation Time (ROT)
Item
Door Trim Upper Veneer Panel-Renew
Door Trim Upper Veneer Panel-Renew
Removal
1. Remove door trimboard assembly (see Workshop
Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access & Refit).
2. Remove screws (x9), release clip securing trim upper
veneer panel to trimboard, and remove trim panel.
Installation
1. Install trim upper veneer panel, install clip, install and
tighten screws (x9).
2. Install door trimboard assembly ((see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door -
Remove for Access & Refit).

LH Door Trim Upper Panel-Renew

Repair Operation Time (ROT)
Item
Door Trim Upper Panel-Renew
Door Trim Upper Panel-Renew
Removal
1. Remove door trimboard assembly (see Workshop
Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access & Refit
2. Remove upper veneer door trim panel securing screws
(x9) and clip (x1).
3. Remove speaker grille securing screws (x2) and unclip
(x3) from panel.
4. Remove upper door trim panel securing screw (x1) and
drill out 7 pop-rivets
Installation
1. Install upper door trim panel, securing screw (x1) and
pop-rivets (x7).
1-4-4
2. Install speaker grille, clips (x3) and screws (x2).
3. Install upper veneer door trim panel, screws (x9) and
clip (x1).
4. Install door trimboard assembly (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door ­
Remove for Access & Refit).
RH/LH Interior Door Assembly Handle
and Armrest-Renew
Repair Operation Time (ROT)
Item
Interior Door Handle and Armrest-
Renew
Interior Door Handle and Armrest-
Renew
Removal
1. Open door.
2. Remove bolts (x2) securing interior door handle and
armrest.
Code
3. Disconnect latch inner and outer cable from handle,
RH 01.05.CC
remove handle/armrest assembly.
LH 01.05.CD
Installation
1. Connect latch inner and outer cable to handle
mechanism.
2. Install handle/armrest assembly to trimboard, install and
tighten bolts (x2).

RH/LH Door Pocket Assembly-Renew

Repair Operation Time (ROT)
Item
Door Pocket Assembly-Renew
Door Pocket Assembly-Renew
Removal
1. Remove door trimboard assembly (see Workshop
Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access & Refit).
2. Remove door ajar puddle lamp.
Code
3. Remove nuts (x10), securing door pocket to trimboard,
RH 01.05.CE
remove door pocket.
LH 01.05.CF
Installation
1. Install door pocket, install and tighten nuts (x10).
2. Install door ajar puddle lamp.
3. Install door trimboard assembly (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door ­
Remove for Access & Refit).
Lower Panel Assembly Quarter Trim-
Renew
Repair Operation Time (ROT)
Item
Lower Panel Assembly Quarter Trim-
Renew
Workshop Manual
Code
RH 01.05.CG
LH 01.05.CH
Code
RH 01.05.CJ
LH 01.05.CK
Code
RH 01.05.CR
October 2005