Maintenance; Transaxle Harness-Renew; Centre Stack Harness-Renew; Passenger Door Harness-Renew - Aston Martin V8 Vantage Workshop Manual

Maintenance

Transaxle Harness-Renew

Repair Operation Time (ROT)
Item
Transaxle Harness-Renew
Removal
1. Remove RH Wheel arch liner (see Workshop Manual
procedure 01.02.HB Wheel Arch Liner - Rear - RH -
Renew).
2. Remove rear undertray (see Workshop Manual
procedure 01.02.PB Undertray - Rear - Renew).
3. Disconnect transaxle multiplug from body harness.
4. Release harness from RH wheel arch (clips x2).
5. Disconnect LH and RH pad wear sensor multiplug (X2).
6. Disconnect load level sensor multiplug.
7. Disconnect LH and RH ABS sensor multiplugs (x2)
8. Disconnect reverse light switch and release harness from
transaxle (clips x2).
9. Release harness clips (x23) from subframe and toe
control arms.
Installation
1. Secure harness clips (x23) to subframe and toe control
arms.
2. Connect reverse light switch multiplug and secure
harness clips (x2) to transaxle.
3. Connect ABS sensors
4. Connect load level sensor.
5. Connect pad wear sensor multiplugs.
6. Connect transaxle multiplug and secure harness to
wheel arch.
7. Install rear undertray (see Workshop Manual procedure
01.02.PB Undertray - Rear - Renew).
8. Install RH rear wheel arch liner (see Workshop Manual
procedure 01.02.HB Wheel Arch Liner - Rear - RH -
Renew).

Centre Stack Harness-Renew

Repair Operation Time (ROT)
Item
Centre Stack Harness-Renew
Removal
1. Disconnect vehicle battery.
2. Remove centre stack assembly (see Workshop Manual
procedure 15.01.CB Centre Stack Assembly - Remove
for Access & Refit).
3. Remove CD player, screws (x2) and disconnect
multiplug.
4. Release harness clips (x7), remove harness.
Installation
1. Install harness and secure with clips (x7).
October 2005
Electric Distribution/Electronic Control (18.00)
2. Position CD player, connect multiplug, install and
torque tighten screws (x2).
3. Install centre stack assembly (see Workshop Manual
procedure 15.01.CB Centre Stack Assembly - Remove
for Access & Refit).
Code
4. Connect vehicle battery.
18.01.DL

Passenger Door Harness-Renew

Repair Operation Time (ROT)
Item
Passenger Door Harness-Renew
Removal
1. Remove LH door glass regulator (see Workshop Manual
procedure 01.11.DB Regulator - Door Glass - LH -
Renew).
2. Remove bolts (x4) door control module to door.
3. Disconnect multiplugs (x3) and remove door control
module.
4. Remove bolts (x3) side impact mounting plate to door.
5. Disconnect multiplug to side impact sensor and remove
plate.
6. Disconnect multiplug to door speaker.
7. Disconnect multiplug to door mirror.
8. Disconnect multiplug to door latch assembly.
9. Release harness from inner door casing clips (x10).
10. Release harness from outer door casing clips (x8).
11. Release harness grommets from door casing (x2).
12. Remove harness.
Installation
1. Position harness in door and install grommets (x2).
2. Secure harness in door casIng clips (x18).
3. Connect multiplug to door latch.
4. Connect multiplug to door mirror
5. Connect multiplug to door speaker.
6. Connect multiplug and install side impact mounting
plate to door (x3).
7. Connect multiplugs (x3) and install door control
module.

Driver's Door Harness-Renew

Code
Repair Operation Time (ROT)
18.01.FC
Item
Driver's Door Harness-Renew
Removal
1. Remove drivers door glass regulator (see Workshop
Manual procedure 01.11.DA Regulator - Door Glass -
RH - Renew).
2. Remove bolts (x4) drivers door control module to door.
3. Disconnect multiplugs (x3) and remove module.
4. Remove bolts (x3) plate to door.
5. Remove plate.
6. Disconnect multiplug to door speaker.
Workshop Manual
Wiring and Circuit Protection (18.01)
Code
18.01.GD
Code
18.01.GH
18-1-11