Table of Contents
Advertisement
Fuel Tank and Lines (10.01)
Fuel (10.00)
5. Install luggage compartment rear floor carpet
6. Connect battery earth lead.
Fuel Vapour Pipe Assembly-Renew
Repair Operation Time (ROT)
Item
Fuel Vapour Pipe Assembly-Renew
Removal
1. Battery isolation switch off.
2. Remove RH front wheel arch liner (see Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
3. Disconnect quick fit connector fuel vapour pipe to tank.
4. Release fuel vapour pipe from fuel line clips (x4).
5. Disconnect quick fit connector fuel vapour pipe
assembly to purge valve 'T' piece.
6. Remove fuel vapour pipe.
Installation
1. Install fuel vapour pipe and connect to purge valve 'T'
piece.
2. Position fuel vapour pipe in vapour line clips.
3. Connect fuel vapour pipe to fuel tank.
4. Install RH front wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
5. Battery isolation switch on.
Fuel Supply and Vapour Pipe Assembly-
Renew
Repair Operation Time (ROT)
Item
Fuel Supply and Vapour Pipe Assembly-
Renew
1. Depressurise fuel system (see Workshop Manual
procedure 10.01.EK Fuel System - Depressurise).
2. Disconnect vehicle battery.
3. Remove RH front wheel arch liner (see Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
4. Position container to collect spillage from fuel supply
pipe.
5. Disconnect quick fit connector fuel supply pipe to tank
6. Release pipe assembly from fuel line clips (x3).
7. Disconnect quick fit connector fuel supply to manifold
supply (fuel rail) and remove pipe assembly.
Installation
1. Connect fuel supply pipe to manifold supply pipe.
2. Position fuel line in fuel line clips (x3).
3. Connect fuel supply pipe to tank.
4. Install RH front wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
10-1-10
5. Connect vehicle battery.
Manifold Supply Fuel Pipe Assembly-
Renew
Repair Operation Time (ROT)
Item
Code
Manifold Supply Fuel Pipe Assembly-
10.01.KA
Renew
Removal
1. Depressurise fuel system (see Workshop Manual
procedure 10.01.EK Fuel System - Depressurise).
2. Disconnect vehicle battery
3. Remove RH wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Position container to collect fuel spillage.
5. Release fuel supply and vapour pipe from pipe clips (3).
6. Disconnect quick fit connector Manifold supply pipe to
fuel supply and vapour pipe.
7. Disconnect manifold supply pipe from fuel rail.
8. Release manifold supply pipe from pipe clips (x3) and
remove pipe.
Installation
1. Position manifold supply pipe and secure in clips (x3).
2. Connect manifold supply pipe to fuel rail.
3. Connect manifold supply pipe to fuel supply and vapour
pipe.
4. Secure fuel supply and vapour pipe in clips (x3).
5. Install wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
Code
6. Connect vehicle battery.
10.01.KB
Fuel Tank Filler Hose Assembly-Renew
Repair Operation Time (ROT)
Item
Fuel Tank Filler Hose Assembly-Renew
Removal
1. Remove fuel tank assembly (see Workshop Manual
procedure 10.01.GA Tank and Canister Assembly - Fuel
- Remove for Access and Refit).
2. Release clip and disconnect fuel tank filler hose from
inside tank.
3. Release fuel filler hose from bracket and remove hose.
Installation
1. Position fuel filler tank hose to tank outlet and secure
with clip.
2. Secure fuel filler tank hose to bracket.
3. Install fuel tank assembly (see Workshop Manual
procedure 10.01.GA Tank and Canister Assembly - Fuel
- Remove for Access and Refit).
Workshop Manual
Code
10.01.KC
Code
10.01.LB
October 2005
Advertisement
Chapters
Table of Contents
